91 mazda 626, door lock actuator

Home / the12volt's Install Bay / Relays / 91 mazda 626, door lock actuator (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

jpawloski

Member - Posts: 9

Joined: May 14, 2003

Location: Canada

Posted: May 20, 2003 at 2:25 PM / IP Logged

HI,

I have a problem with the door lock actuator i just bought, i have it all hooked up correctly with the 2 relays, wired from the acutator digram on this site. The actuator will only go into the unlock position and will not do anything else, it just freezes in the unlock postion......i am using a Impact Auto security alarm system...

can anyone help...im still new at this.....

yodo

Member - Posts: 19

Joined: April 24, 2003

Location: Australia

Posted: May 23, 2003 at 7:30 PM / IP Logged

Hey Bro, I just put an alarm into my mx6. i added all new actuators to each door with the relay. It's not your relay! It's the way you hooked it up to your alarm. I dont know much about with your brand of alarm but mine had 4 ways to wire the central locking to the alarm unit. Sounds like you have it to the negative trigger. This to happened to me. Look closely at the wiring diagrams and the chances are one wire is wrong. It's hard to say without the diagram but its easy.

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: May 23, 2003 at 10:49 PM / IP Logged

Try this setup on the relays: Adding Door Lock Actuators Diagram

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

jpawloski

Member - Posts: 9

Joined: May 14, 2003

Location: Canada

Posted: May 23, 2003 at 11:57 PM / IP Logged

hi,

thanks for the replys,

ive done all the wiring according to the diagrams..but my alarm has two negative "1green, 1 violet"..door lock wires.................and then it has a extra deal called a door lock plug that comes with the alarm, and has green, blue, and red for 12v. The only way i get a response is if i attact the blue wire from the door plug, but then it just extends the actuator and won't move at all, it just stays stuck............its getting to be quite annoying.............oh well.....if anyone could help that would be awesome...

Thanks In Advance

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: May 24, 2003 at 11:33 AM / IP Logged

Which wires did you use for the actuator ? From what you have listed above, you should have used the GREEN & the BLUE wires for lock/unlock and the RED wire would be your polarity selector.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

jpawloski

Member - Posts: 9

Joined: May 14, 2003

Location: Canada

Posted: May 24, 2003 at 12:16 PM / IP Logged

I used the green and blue from the door plug wire. I am still new to this, bare with me. What do you connect the red wire too? THe manual on this alarm is like 1 page its very sad..lol.............

thanks

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: May 24, 2003 at 4:22 PM / IP Logged

Try this:

Test the output of the BLUE & GREEN wire when you leave the RED wire not connected to anything.
Test the output of the BLUE & GREEN wire when you connect it to 12 volts +

Post your results.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

91 mazda 626, door lock actuator

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.