Side Markers

Home / the12volt's Install Bay / Relays / Side Markers (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

DjIQ

Copper - Posts: 107

Joined: March 10, 2003

Location: United States

Posted: September 15, 2003 at 6:50 AM / IP Logged

I need to wire my side markers so that they:

Turn ON when I turn ON my PARKING LIGHTS

are still ON with my DRIVING LIGHTS

and FLASH with my TURN SIGNALS

auex

Platinum - Posts: 5,041

This member has made a donation to the12volt.com. Click here for more info.

Joined: December 23, 2002

Location: Arizona, United States

Posted: September 15, 2003 at 9:24 PM / IP Logged

First you will need two relays. For the left side wire it this way: 85 ground, 86 left turn signal wire ( the wire that pulses +12V when left turn signal is on), 30 parking light input ( wire that has +12V when parking lights are on and when headlights are on), 87A output to left marker light. Do the same for the right side.

Certified Security Specialist

Always check info with a digital multimeter.

I promise to be good.

Tell Darwin I sent you.

I've been sick lately, sorry I won't be on much.

fatheadjames

Member - Posts: 7

Joined: December 16, 2002

Location: United States

Posted: September 22, 2003 at 5:35 PM / IP Logged

what if you also wanted them to work with the turn signals with the lights off?

fireman1321

Member - Posts: 20

Joined: September 10, 2003

Location: United States

Posted: September 22, 2003 at 8:19 PM / IP Logged

what auesx has posted above should make them flash with your signals and if you have an alarm and light flash they will flash with those.

Future Fire Man

fatheadjames

Member - Posts: 7

Joined: December 16, 2002

Location: United States

Posted: September 22, 2003 at 9:28 PM / IP Logged

well I wired them like he said and the turn signals would only work with the running lights on. Switched the wires and the opposite happened. So this is where I'm stuck at. It is a 1990 rodeo. What I'm trying to do is shave the turn signal /running light at the bottom and make the running light on the corner act as both turn signal and running light.

fireman1321

Member - Posts: 20

Joined: September 10, 2003

Location: United States

Posted: September 23, 2003 at 4:44 PM / IP Logged

ohhhh, ok... basically what you need to do is take the wires that go to the bumper turn signals and tap the leads from the wires going to your running lights and tap them into the bumper lights... I have a '95 isuzu pickup and I have side markers that blink with my bumpers... if you want to use a relay you want to use the power from the blinkers and have them power your running and sidemarkers... I dont have time to figure out the relay outline, but I will post it tonight.

Future Fire Man

fatheadjames

Member - Posts: 7

Joined: December 16, 2002

Location: United States

Posted: September 24, 2003 at 1:53 PM / IP Logged

Whenever you get the chance that would be much appreciated.

fireman1321

Member - Posts: 20

Joined: September 10, 2003

Location: United States

Posted: September 25, 2003 at 2:06 PM / IP Logged

ok, there is no other easier way to do this but you need 4 relays.... kinda of a lot but you need them to have this work properly...

(1st relay on left side) 85 & 87-lower voltage blinker wire on left side; 86-ground from blinker light; 87a-nothing; 30-one side marker and/or running light.

(2nd relay on left side) 85&87-higher voltage blinker wire on left side; 86- bround from blinker light; 87a-nothing; 30-other side of marker and/or running light.

(3rd & 4th relay on right side)vise versa...

if that doesnt work let me know. good luck.

Future Fire Man

artkam

Member - Posts: 1

Joined: October 24, 2003

Location: Poland

Posted: October 24, 2003 at 1:07 PM / IP Logged

...there is other way to get this function working...this is my personal project which is called "light automation system". Basically this is an electronic module which is turning ON Head lights & Tail lamps, but after receiving signal from both, oil sensor and charge battery control lamp(alternator charge control). This function helps driver in remember about obligation to turn ON LAMPS over the day. Such a policy works here through the half of the year. Ok, regarding to this problem, based on this module is possible to wire tail lamps by sides(independent), so they can be "overdriven" by module. Next step is to connect trigger from blinker (relay) and from tail lamp switch (or relay(s)), or from side markers. Whatever combination is necessary or if you have any question regarding to my project(s), just let me know, i can send you connection diagram also. Modules are based not on relays and are protected. There is also possible to design SPECIAL FUNCTION electronic module, based on your specific needs....

Thanks for reading, Artur..

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Side Markers

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.