the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

08 equinox, pass key


Post ReplyPost New Topic
< Prev Topic Next Topic >
bigwd 
Member - Posts: 8
Member spacespace
Joined: December 03, 2007
Location: Texas, United States
Posted: April 29, 2008 at 11:24 PM / IP Logged  
what up i hhave a big problem the wires for pass key is switched do any one have any info would be helpful thanx
bigwd 
Member - Posts: 8
Member spacespace
Joined: December 03, 2007
Location: Texas, United States
Posted: April 30, 2008 at 9:18 AM / IP Logged  
a bd again a photo would b help ful for antana where the plug wires for module  thanx
bbullers 
Copper - Posts: 76
Copper spacespace
Joined: April 16, 2008
Location: Illinois, United States
Posted: May 01, 2008 at 12:36 AM / IP Logged  
No offense, but we could probibly help you if we knew what you were asking..... You haven't asked a real question, we don't know what year, make, or model, your vehicle is, or what you're trying to do..... for us to help you, we need specifics.... as many as you can give.   Are you trying to install a remote start, alarm, what? When you respond with these answers, I bet you'll get the answers, you're looking for.... Like Jerry Maguire said... Help Me Help You
The Only Stupid Question, is the one Un-asked
bbullers 
Copper - Posts: 76
Copper spacespace
Joined: April 16, 2008
Location: Illinois, United States
Posted: May 01, 2008 at 12:47 AM / IP Logged  

here's a random stab in the dark.....

YELLOW and ORANGE / BLACK 

GM's PASSLOCK 2 System, wires are in Ignition Switch Harness

GM's PASSLOCK 2 ANTI-THEFT System, Requires 791 Bypass Module

This vehicle for REMOTE STARTING DOES NOT REQUIRE the connection to the STARTER/CRANK wire, the vehicle will Crank when it see power to the IGNITION and then the droping out of voltage on the ACCESSORY wire will automaticlly start the vehicle. The installation of the 791 Bypass Module DOES require a connection to the STARTER CRANK wire, to make the 791 work you will need to do this. Take the YELLOW/BLACK from the 791 and apply it to 12 volts constant while cranking the vehicle with the ignition key, after the vehicle starts, take the YELOW/BLACK wire from the 791 off of the 12 volts constant. in 10 to 20 seconds the RED light in the 791 will turn off. Repeat this step 2 more times, the RED light in the 791 will turn on and then off each time, turn the vehicle off and then tape the YELLOW/BLACK wire from the 791 up and do not use.

The Only Stupid Question, is the one Un-asked

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Tuesday, April 30, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer