need info on 1998 plymouth remote wiring

Home / the12volt's Install Bay / Vehicle Wiring Information & File Requests / need info on 1998 plymouth remote wiring (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

rodlyz

Member - Posts: 1

Joined: September 07, 2005

Location: Canada

Posted: September 07, 2005 at 9:44 PM / IP Logged

need info on 1998 plymouth breeze remote start wiring particularly on the door lock/unlock wiring...

Back to Top

chungo

Copper - Posts: 135

Joined: December 31, 2003

Location: United States

Posted: September 07, 2005 at 9:50 PM / IP Logged

12volts	red, pink/black	+	ignition harness
Notes: When doing remote start red should not be used for main power. Use pink/black.
Starter	yellow	+	ignition harness
Second Starter
Ignition	dark blue	+	ignition harness
Second Ignition	GREEN/ red	+	ignition harness
Third Ignition
Accessory	blk/orn & blk/wht	+	ignition harness
Second Accessory
Keysense
Power Lock	WHITE/ green	+	rear of fuse box under dash
Notes: Use positive (+) trigger thru a 620 ohm resistor to lock, and a positive (+) trigger thru a 2.7K ohm resistor to unlock. Must use relays.
Power Unlock	same wire
Lock Motor	ORANGE / black	+	drivers kick panel
Unlock Motor	blue/white	+	drivers kick panel
Parking Lights+	BLACK / YELLOW		dr kick or behind fuse box
Parking Lights-
Hazards
Turn Signal(L)
Turn Signal(R)
Reverse Light
Door Trigger	yellow	-	front of fusebox
Notes: In a three (3) pin connector near the door jam.
Dome Supervision
Trunk/Hatch Pin	tan/black	-	driver kick panel
Hood Pin
Trunk/Hatch Release	BLACK/ white	+	driver kick panel
Power Sliding Door
Factory Alarm Arm	GREEN/ orange	+	kick or BCM
Notes: Lt.GREEN/ orange from drivers door or dk.GREEN/ orange from passenger or catch either at BCM located behind right side dash. Use a positive (+) trigger thru a 940 ohm resistor to arm, and a positive (+) trigger thru a 470 ohm resistor to disarm. Must use relays.
Factory Alarm Disarm	same wire
Disarm No Unlock
Tachometer	BLACK/ gray	AC	coil pack
Notes: 6 cylinder signal on the V-6, 2 cylinder signal on the 4 cylinder engine. If BLACK/ gray on V6 causes starter to drag, use any one of the fuel injection wires at injectors at front of engine and set to one cylinder. The injector wire will be the one that IS NOT dk.GREEN/ orange.
Wait to start
Brake Wire	WHITE/ tan	+	at brake switch
Parking Brake
Horn Trigger	BLACK/ red	-	steering column
Memory Seat 1
Memory Seat 2
Memory Seat 3

Interface Module:	Category: Immobilizer Bypass	Required: No	Type: N/A
Part #: N/A
Notes:
Interface Module:	Category: Door Lock Interface	Required: Yes	Type: Multiplex
Part #: 456LW
Notes:

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

need info on 1998 plymouth remote wiring

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.