viper 5701 alarm/remote start, 99 legacy

First off would like to say how helpful posts in this forum has been! I recently purchased a viper 5701 and am trying to install it into a 1999 subaru legacy. I've wired all main wires in apart from door looks, When i plug the viper brain unit in nothing happens, the LED on the control module doesnt blink at all, just seems dead? These are my connections Main Harness, 6-pin connector H1/1 Red (+) 12VDC Constant Input -> constant 12v H1/2 Black (-) Chassis Ground -> grounded H1/3 Brown (+) Siren Output -> red wire to siren H1/4 WHITE/ Brown Parking light isolation wire -> Not Used H1/5 White Parking light output -> Not done yet H1/6 Orange (-) Ground when armed -> i just grounded this Remote Start, (+) 10-pin heavy gauge connector @ Ignition Switch Harness H3/1 Pink Ignition 1 Input/Output -> ign @ ignition harness H3/2 RED / White Fused (30A) Ignition 2 / Flex relay input 87 -> 12v const H3/3 Orange Accessory Output -> acc @ ignition harness H3/4 Violet Starter Output (Car side of the starter kill) -> not done yet H3/5 Green Starter Input (Key side of the starter kill) -> not done yet H3/6 Red Fused (30A) Ignition 1 Input -> 12v const H3/7 Pink/White Ignition 2 / Flex Relay Output -> not used H3/8 Pink/Black Flex Relay Input 87A key side (if required) of Flex Relay ->not used H3/9 RED / Black Fuse (30A) Accessory/Starter Input -> 12v const Auxiliary/Shutdown/Trigger Harness, 24-pin connector H2/1 Pink/White (-)200mA Ignition / Flex Relay control output -> Not used when doing remote start H2/2 BLACK/ White (-) Neutral Safety Input -> neutral gearbox sensor H2/3 Blue/White (-)200mA 2nd Status / Rear Defogger Output -> Not used H2/4 GREEN/ Black (-)200mA OEM Alarm Disarm Output -> Not used H2/5 RED / White (-)200mA Trunk Release Output -> Not used H2/6 Green (-) Door Trigger Input -> dome door light H2/7 BLACK / YELLOW (-)200mA Dome ligh supervision -> Not used H2/8 BROWN / Black (-)200mA Horn Honk Output -> Not used H2/9 Dark Blue (-)200mA Status Output -> Not used H2/10 Pink (-)200mA Ignition 1 Output - > Not used when doing remote start H2/11 WHITE/ Black (-)200mA AUX 3 Output -> Not Used H2/12 Violet (+) Door Trigger input -> Not Used H2/13 WHITE/ Violet Aux 1 Output -> Not Used H2/14 Violet/Black Aux 2 Output -> Not Used H/2/15 Orang/Black Aux 4 Output -> Not Used H2/16 Brown (+) Brake Shutdown Input -> + @ Brake Switch Harness H2/17 Grey (-) Hood Pin Input -> hood pin H2/18 Violet / YELLOW (-)200mA Starter Output -> Not used when doing remote start H2/19 Blue (-) Trunk Pin/ Instant trigger input -> Not used H2/20 Grey/Black (-) Diesel Wait to start -> Not used H2/21 WHITE/ Blue (-) Remote start/ Turbo timer activation input -> Not Used H2/22 Orange (-) 200mA Accessory Output -> Not used when doing remote start H2/23 Violet/White Tachometer input -> not done yet H2/24 Green White (-) 200mA OEM Alarm Arm Output -> Not used I double checked the power and ground going to h1/1 and h1/2 seed fine, am i missing something here? or is the unit defective? Thanks

Remove the ORANGE from ground.

cool will give it a shot tomorrow morning and let you know!

disconnected orange cable, no luck. LED status light still not lighting.

Antenna and LED plugged in?

Yes, the antenna and the led are one unit on the viper 5701. Its called the "control unit" in the manual. Does it sound like a faulty box? I've removed the power harness and tested it theres a constant 12v going to it.

Have you tested voltage across H1 black and red?

yes thats the one i was testing, i would assume at a a minimum that would be enough to to get the led to blink/brain to function. The remotes that came with it haven't been factory paired so i need the control centre to work for pairing.

OK then it isn't working because you haven't paired the remotes. Make sure H1/1 red and H2/6 green show 12V+ when you open a door.

will try and get back, Thanks howie ll