2002 Ram Remote Start

Home / the12volt's Install Bay / Car Security and Convenience / 2002 Ram Remote Start (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

wvumounty

Member - Posts: 11

Joined: November 16, 2002

Location: United States

Posted: April 07, 2003 at 7:28 AM / IP Logged

I have my remote start and keyless entry working, all except the Air Conditioner. I am guessing I missed an accessory wire? Any help would be greatly appreciated.

Trav3D1

Copper - Posts: 146

Joined: April 06, 2003

Location: United States

Posted: April 07, 2003 at 12:01 PM / IP Logged

Most 2002 Dodge Rams have 2 accessory wires in the ignition harness.......the colors should be BLACK/ white and blue. You will need to connect the accessory wire from the alarm to both of the wires in order for the AC to work. The second of the two wires will require a relay.

Let me know if your uncertain how to hook this up and I will send you the specs.

Jazz3D1@excite.com

Trav

wvumounty

Member - Posts: 11

Joined: November 16, 2002

Location: United States

Posted: April 07, 2003 at 12:12 PM / IP Logged

My alarm has two wires for accessory. I hooked up accessory 1 from alarm to

1st accessory to truck and second to each. Can you send me the specs and I

will double check? Any other ideas?

Trav3D1

Copper - Posts: 146

Joined: April 06, 2003

Location: United States

Posted: April 07, 2003 at 12:24 PM / IP Logged

This is were the relay comes into play, because AC is usually requires high current. This is also very typical if you have a front and a rear unit that operate seperate from one another.

Do you want the vehicle specs. or the relay specs.

Trav

wvumounty

Member - Posts: 11

Joined: November 16, 2002

Location: United States

Posted: April 07, 2003 at 12:30 PM / IP Logged

I need the relay specs... so you are saying put the relay on the second wire? (blue wire)

Thanks again

-Jeff

JWorm

Platinum - Posts: 2,208

Joined: December 11, 2002

Location: New Hampshire, United States

Posted: April 07, 2003 at 6:34 PM / IP Logged

your truck has two ignitions and 2 accessories.

12volts pnk/blk & RED / wht

Starter yellow

Ignition blue (16 awg)

Second Ignition red or RED / wht

Accessories green & orange

CCRoadshop

Copper - Posts: 70

Joined: April 01, 2003

Location: United States

Posted: April 08, 2003 at 12:02 AM / IP Logged

take a relay and hook the RED / brown wire up to twelve volts, hook the black wire to the ribbon cable color of the accessory wire on the remote start(in most cases orange, and then hook the yellow up to the 2nd accessory wire.....if these colors arent on your relay...lemme know ill tell u what pins to hook up

Installer - Circuit City Roadshop(2 1/2 years n counting)

------------------

Alpine CDA7894(soon to be the cda9815)

Pioneer XM unit(soon to be direct link alpine)

Audiovox 995C alarm/remote start

wvumounty

Member - Posts: 11

Joined: November 16, 2002

Location: United States

Posted: April 09, 2003 at 7:12 AM / IP Logged

These are the wires I am using and currently have hooked up. I have a second ignition wire in my remote. My relay does not have wires only pins...87,86,87a,85 and 30. Can you tell me how to wire the relay?

IGNITION |blue (16 awg)

| SECOND IGNITION |red or RED / wht

| ACCESSORY |green & orange

| SECOND ACCESSORY |blue & blk/wht

Homicyde

Member - Posts: 20

Joined: March 24, 2003

Location: United States

Posted: April 09, 2003 at 9:30 PM / IP Logged

you will need 2 seperate relays, one for the green and one for the orange. take pin 87, hook it to fused 12 volts. pin 86, fused 12 volts. pin 85, needs to be a ground only when the remote starter is running the engine. And pin 30, goes to the green and orange wires. just dont forget to use a relay for each wire.

chris-

wvumounty

Member - Posts: 11

Joined: November 16, 2002

Location: United States

Posted: April 21, 2003 at 7:09 AM / IP Logged

Thanks that worked great. I have another problem. When I unlock/lock the doors all that blinks is the dashboard, the parking lights don't flash.

However if I have the key to the on position, the lights flash.

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.