2011 mazda 3 dball problems

Home / the12volt's Install Bay / Car Security and Convenience / 2011 mazda 3 dball problems (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

lurch228

Silver - Posts: 1,338

Joined: August 08, 2012

Posted: November 27, 2012 at 5:17 AM / IP Logged

DMM Check the H2/3 Brown brake wire input as it should only have +12v on it when the foot brake is pressed.

lurch228

Silver - Posts: 1,338

Joined: August 08, 2012

Posted: November 27, 2012 at 5:21 AM / IP Logged

H2/1 BLACK/ White should be grounded for a Automatic Trans.

lucasoil4u

Copper - Posts: 317

Joined: May 11, 2009

Location: Minnesota, United States

Posted: November 27, 2012 at 8:31 AM / IP Logged

Both of those are true. Sometimes it works most of the time 5 flashes. Bad Brain?

lucasoil4u

Copper - Posts: 317

Joined: May 11, 2009

Location: Minnesota, United States

Posted: November 27, 2012 at 8:32 AM / IP Logged

Hardwired Green in DKP. shows 12 volts when brake is pressed.

offroadzj

Gold - Posts: 2,043

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: June 03, 2005

Location: New York, United States

Posted: November 27, 2012 at 8:53 AM / IP Logged

I would just test and make sure that the wire doesn't somehow show voltage with the ignition on to make sure, but it sounds like possibly a bad brain. Is the DBALL W2W or D2D? If D2D, try changing it to W2W in case there is a miscommunication from the DBALL to the Viper Brake shutdown.

Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205

lucasoil4u

Copper - Posts: 317

Joined: May 11, 2009

Location: Minnesota, United States

Posted: November 27, 2012 at 9:02 AM / IP Logged

The DBALL was removed and a PKALL was installed. So the Viper brain is used for the brake shutdown. Brown wire to green in DKP. only shows 12 volts when brake is applied. Im getting 5 flashes when trying to start or go into Pit Stop mode.

offroadzj

Gold - Posts: 2,043

Joined: June 03, 2005

Location: New York, United States

Posted: November 27, 2012 at 11:08 AM / IP Logged

I just brought up the install guide and it shows that 5 flashes is the hood, not the brake. How do you have the gray hood pin wire connected? Test to see if that is showing ground.

Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205

lucasoil4u

Copper - Posts: 317

Joined: May 11, 2009

Location: Minnesota, United States

Posted: November 27, 2012 at 11:21 AM / IP Logged

gray is the small gray wire on the 5 pin harness. Connected to nothing. I havent ran that yet. I was gonna get a mercury switch cause this is the wifes car. The neutral Safety switch is hooked threw a switch to ground. Wire isnt hooked to anything yet. Is the Brain Bad?

offroadzj

Gold - Posts: 2,043

Joined: June 03, 2005

Location: New York, United States

Posted: November 27, 2012 at 1:08 PM / IP Logged

Put your meter on the gray hood pin wire and see if it shows ground. If so and it isn't connected then the brain is bad. Also make sure you have a ground signal on the NSS. Check both directly at the connector to the brain.

Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205

lucasoil4u

Copper - Posts: 317

Joined: May 11, 2009

Location: Minnesota, United States

Posted: November 27, 2012 at 2:00 PM / IP Logged

I will do this after work. Thanks man

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.