the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2010 Toyota Tundra Alarm/Remote Start/Stereo Wiring


Post ReplyPost New Topic
< Prev Topic Next Topic >
goofballtech 
Member - Posts: 3
Member spacespace
Joined: August 14, 2009
Location: Louisiana, United States
Posted: August 14, 2009 at 9:49 AM / IP Logged  

Great Information richl68. Thanks

Would you happen to have the information on the wiring for the back up cam too? Or a schmatic drawings that would include the camera circuit?

Thanks in advance.

2010 Tundra DC 5.7
1996 Tacoma (Off Road Beast)
feroz 
Member - Posts: 21
Member spacespace
Joined: April 11, 2009
Location: California, United States
Posted: August 19, 2009 at 9:42 AM / IP Logged  
wow thats some great information, Thank You Rich168
2010 Tundra
feroz 
Member - Posts: 21
Member spacespace
Joined: April 11, 2009
Location: California, United States
Posted: August 22, 2009 at 6:02 PM / IP Logged  

Question about the door Trigger.

Has anyone used this for door trigger, as it stays on for a few seconds after door is closed?

All Door TriggerORANGE(-)AT COURTESY LIGHT UNDER DASH

2010 Tundra
goofballtech 
Member - Posts: 3
Member spacespace
Joined: August 14, 2009
Location: Louisiana, United States
Posted: August 28, 2009 at 12:50 PM / IP Logged  
I used each individual door trigger. two under the passenger kick plate for that side. One in driver's kick plate and one under the flashing by you knees below the column. They work great for my Amp Research Power Steps.
2010 Tundra DC 5.7
1996 Tacoma (Off Road Beast)
feroz 
Member - Posts: 21
Member spacespace
Joined: April 11, 2009
Location: California, United States
Posted: August 31, 2009 at 11:44 PM / IP Logged  

Hi,

I have lock/unlock issues, the doors lock fine but does not unlock when disarmed, I have factory keyless entry but no factory alarm, I am using the following wires.(I am using the Neg door lock/unlock). The alarm/remote start I am installing is the viper 5901.

Thanks for all the help!!

Factory Alarm Armlt. blue to purple-driver kick, blue 17 pin plug, pin 14
Meter this wire while turning the key in the driver door key cylinder. This wire will also lock the doors.
Factory Alarm Disarmpink to black (double pulse)-driver kick, blue 17 pin plug, pin 16

richl68 
Copper - Posts: 107
Copper spacespace
Joined: June 20, 2009
Location: New Jersey, United States
Posted: September 01, 2009 at 4:35 PM / IP Logged  
Did you program double pulse for your unlock or disarm? when you goto unlock the door if you hit the unlock button twice does the doors unlock?
feroz 
Member - Posts: 21
Member spacespace
Joined: April 11, 2009
Location: California, United States
Posted: September 01, 2009 at 11:49 PM / IP Logged  

I got it figured out, the unlock alarm wire was not connected properly, Thank you rich168.

I got everything to work but not sure if there is a problem of what i did. I had to jump the ACCESSORY and the SECOND IGNITION wire for the AC to work when remote starting. The second ignition wire from the viper 5901 did not output +12v when remote starting.

Doing what I did solved the issue BUT I am wondering if this will be a problem later on?

Any and all input will be appreciated.

Many thanks!

2010 Tundra
richl68 
Copper - Posts: 107
Copper spacespace
Joined: June 20, 2009
Location: New Jersey, United States
Posted: September 07, 2009 at 3:47 PM / IP Logged  

your 2nd ignition wire is pink/white? in the manual for the remote start i believe you can change the 2nd ign to 2nd acc

wiring diagrams are nice but sometimes they can be wrong, ive come across plenty of cases when it says it is ign but ends up being a acc wire.

feroz 
Member - Posts: 21
Member spacespace
Joined: April 11, 2009
Location: California, United States
Posted: September 08, 2009 at 12:10 PM / IP Logged  

You are right about the 2nd ignition wire, its pink/white. I did try to change it to 2nd acc throught the alarm but no luck, it only outputs 0.2 v when starting, i guess its just enough to drive a relay (will  i need a relay? )

Its working fine so far as i have it wired!

2010 Tundra
goofballtech 
Member - Posts: 3
Member spacespace
Joined: August 14, 2009
Location: Louisiana, United States
Posted: October 01, 2009 at 12:59 PM / IP Logged  

Just got mine installed yesterday. Working good so far.

Only thing is i have to unlock the doors before i remote start because i can disarm the alarm with it running but it won't unlock the door with the truck running through the viper.... i think it might be a menu setting. Gonna have to look and make sure though.

2010 Tundra DC 5.7
1996 Tacoma (Off Road Beast)
Page of 3

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, May 23, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer