07 dodge nitro remote start problems

Home / the12volt's Install Bay / Car Security and Convenience / 07 dodge nitro remote start problems (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

tbird2340

Copper - Posts: 363

Joined: October 03, 2003

Location: Ohio, United States

Posted: November 23, 2009 at 8:11 PM / IP Logged

Would it be possible that the bypass is bad? I can't think of anything else.. I've quadruple checked all the wiring.. Tried both CH3 and CH5 firmware..

When using the CH3 firmware I can start the vehicle with a hollow key by inserting the transponder in it so I know that is programmed correctly..

When using the CH5 firmware the security light flashes after it starts about 5 times and then shuts off..

tbird2340

Copper - Posts: 363

Joined: October 03, 2003

Location: Ohio, United States

Posted: November 25, 2009 at 7:46 PM / IP Logged

Anyone have any other ideas? Could the bypass be bad?

ck auto

Copper - Posts: 257

Joined: September 20, 2003

Location: Canada

Posted: November 25, 2009 at 9:20 PM / IP Logged

how did you program the chip portion of the bypass?

good luck

kirk

tbird2340

Copper - Posts: 363

Joined: October 03, 2003

Location: Ohio, United States

Posted: November 25, 2009 at 9:27 PM / IP Logged

Thanks for the reply..

This is how I programmed it.. I know it programmed successfully because I can start the car with a hollow key by holding the transponder inside it..

07 dodge nitro remote start problems - Page 4 -- posted image.

ck auto

Copper - Posts: 257

Joined: September 20, 2003

Location: Canada

Posted: November 25, 2009 at 9:44 PM / IP Logged

are you plugged into the blue plug also how many wraps did you do around ing cylinder

good luck

kirk

tbird2340

Copper - Posts: 363

Joined: October 03, 2003

Location: Ohio, United States

Posted: November 25, 2009 at 9:47 PM / IP Logged

Yea, the blue plug.. That's the only spot it fits, right?

I wrapped it around as many times as I could just to test.. Could not keep it staying running..

ck auto

Copper - Posts: 257

Joined: September 20, 2003

Location: Canada

Posted: November 25, 2009 at 9:51 PM / IP Logged

is it wrapped behind skim module or in front of it

good luck

kirk

tbird2340

Copper - Posts: 363

Joined: October 03, 2003

Location: Ohio, United States

Posted: November 25, 2009 at 10:08 PM / IP Logged

I tried both ways..

I also tried the CH5 firmware which doesn't need the ring.. That didn't work either.

ck auto

Copper - Posts: 257

Joined: September 20, 2003

Location: Canada

Posted: November 25, 2009 at 11:29 PM / IP Logged

if you hold pelleet up to ign then try and remote start what does it do when you remote start

good luck

kirk

tbird2340

Copper - Posts: 363

Joined: October 03, 2003

Location: Ohio, United States

Posted: November 26, 2009 at 10:41 AM / IP Logged

When I hold the transponder up to the IGN (without being plugged into the bypass) and try a remote start.. It does the same thing.. Starts, security light flashes, and then shuts off..

Very strange.. Because when I start the car with a key with the chip taken out and the transponder held inside the empty key it starts fine and stays running!

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.