remote start ib tbkiii

Home / the12volt's Install Bay / Car Security and Convenience / remote start ib tbkiii (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

tommy...

Gold - Posts: 1,901

Joined: December 10, 2004

Location: United States

Posted: October 25, 2009 at 7:16 PM / IP Logged

The wrap around the cylinder should kinda look like this... http://documents.audiovox.com/701176.pdf

M.E.C.P & First-Class

Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!

syl20rochon

Copper - Posts: 298

Joined: October 16, 2009

Location: Ontario, Canada

Posted: October 25, 2009 at 7:34 PM / IP Logged

We need to know if it starts with the key inserted into the key cylinder and the tbk disconnected....we need to know if your remote starter is programmed properly and that all ignitions are working good before we suspect the bypass.....

Sylvain Rochon

MECP security specialist

Tech support for remote starters

26 Years of experience counts

I'm here to help.

tommy...

Gold - Posts: 1,901

Joined: December 10, 2004

Location: United States

Posted: October 25, 2009 at 7:40 PM / IP Logged

tommy... wrote:

How about the ring that goes around the ignition cylinder...Just make sure the ring is attached properly to the ignition cylinder...Does it remote start fine with the key in the ignition....? Just dont have both keys showing at the same time...! Meaning when trying the key in the ignition...Make sure the bypass is disconnected...!! Make sure you test the key in the bypass also...Start the vehicle to assure that the key is good...Are those the ones(bypass) that you have to wrap a few times around the ignition cylinder?(the wires that wrap the cylinder are thin and need multiple turns around cylinder) What happens when you remte start...All the lights come on the dash...But it doesnt crank...ETC...? Or it does nothing...?

Echo...echo.......echo

M.E.C.P & First-Class

Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!

joekool

Member - Posts: 20

Joined: September 26, 2003

Location: United States

Posted: October 26, 2009 at 5:30 PM / IP Logged

Yes, I have the wrap around wire on tight and correct... the vehicle doesn't even start with the remote and the key in the ignition so I suppose I have something wired up wrong, huh? I double checked my wiring and everything seemed to be wired correctly. From the vehicle wiring diagram Yellow/black is Ignition 1 and BLACK/ red is ignition 2, is that correct? Can I remove the starter Interrupt? Any suggestions?

Thanks, Joe

syl20rochon

Copper - Posts: 298

Joined: October 16, 2009

Location: Ontario, Canada

Posted: October 26, 2009 at 7:14 PM / IP Logged

12V: WHITE/ Red

Ignition 1: BLACK / YELLOW

Ignition 2: BLACK/ Red

Acc: Blue/Red

Starter: GREEN/ Black or black

Sylvain Rochon

MECP security specialist

Tech support for remote starters

26 Years of experience counts

I'm here to help.

joekool

Member - Posts: 20

Joined: September 26, 2003

Location: United States

Posted: October 26, 2009 at 8:11 PM / IP Logged

Can I remove the starter interrupt relay bypass?

Thanks, Joe

syl20rochon

Copper - Posts: 298

Joined: October 16, 2009

Location: Ontario, Canada

Posted: October 26, 2009 at 8:13 PM / IP Logged

You mean the starter kill relay?

Sylvain Rochon

MECP security specialist

Tech support for remote starters

26 Years of experience counts

I'm here to help.

joekool

Member - Posts: 20

Joined: September 26, 2003

Location: United States

Posted: October 26, 2009 at 8:15 PM / IP Logged

yes, do I have to hook that thing up

Thanks, Joe

syl20rochon

Copper - Posts: 298

Joined: October 16, 2009

Location: Ontario, Canada

Posted: October 26, 2009 at 8:17 PM / IP Logged

Not really cause you have a transponder system in you car.....installing the starting kill relay will only give you double protection. I never install them unless my customer really wants it...

Sylvain Rochon

MECP security specialist

Tech support for remote starters

26 Years of experience counts

I'm here to help.

joekool

Member - Posts: 20

Joined: September 26, 2003

Location: United States

Posted: October 26, 2009 at 8:21 PM / IP Logged

ok I am going to remove it and triple check the ignition wiring...stay tuned

Thanks, Joe

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.