the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

3 wire turn signal replacing 2 wire


Post ReplyPost New Topic
< Prev Topic Next Topic >
chapeau 
Member - Posts: 4
Member spacespace
Joined: December 22, 2009
Posted: December 22, 2009 at 8:48 PM / IP Logged  
I just installed aftermarket 3-wire turn signals on my Honda VTX1300R, replacing the factory signals. The 3-wire signals are dual element, where one element works as a marker and both work as a turn signal. Two of the wires from the 3-wire are direct swap, but the instructions call for the third wire to be connected to the bike's "marker" lights. Since the bike didn't have those, I connected the third wire in parallel with the license plate light, which comes on with the ignition.
Everything works properly, sort of. The turn signals glow when the bike is started, then flash more brightly (and more quickly than the factory signals) when the turn signals are engaged. But after a few minutes, they get too hot to touch.
Obviously I'm drawing too much current to the turn signals. I could just disconnect the third wire, but why won't they work the way I've installed them? Will installing a load resistor in line with each signal work to reduce the current draw?
Any help is appreciated.
Thanks.
i am an idiot 
Platinum - Posts: 13,694
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: December 22, 2009 at 9:40 PM / IP Logged  
A dual element bulb is not meant to burn both elements constantly.  They will overheat.
chapeau 
Member - Posts: 4
Member spacespace
Joined: December 22, 2009
Posted: December 23, 2009 at 5:24 AM / IP Logged  
Thanks for the reply, but I don't think both elements are being lit at the same time except when the turn signal is activated. They seem to be wired correctly, but I have read that when turn signals blink rapidly, they are drawing too much current, and mine now blink rapidly and overheat.
i am an idiot 
Platinum - Posts: 13,694
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: December 23, 2009 at 6:37 AM / IP Logged  
Which element is lit all the time, the dimmer or the brighter of the 2?   Fast blinking usually indicates not enough current draw.  It is a safety mechanism to alert you that there may be a blown bulb.  If you caught the dimmer element for blinker, it may not be ienough of a load, hence the fast blinking.  The higher wattage element being on steady could also explain the heat buildup.   When you said you wanted them both to blink, that is why I thought you had them both on.  If you find out that the elements are backwards and correcting that resolves your heat issues, we can make them both blink for you.  It may take 2 relays per side of bike to accomplish that, but if you have the space, we can make it happen.
chapeau 
Member - Posts: 4
Member spacespace
Joined: December 22, 2009
Posted: December 23, 2009 at 10:14 PM / IP Logged  
The dimmer element is the one that stays on as a marker, and the brighter element comes on as a blinker. The wiring instructions were very clear and easy, as far as doing a 1/1 swap for the 12v and ground. The extra wire from the 3-wire turn signals was supposed to go into the "marker light" circuit, but since that didn't exist on my bike, I paralleled the light for the license plate. That light comes on with the ignition and I figured it was sort of a marker light. Obviously, I've overlooked something. Thanks again for your help.
i am an idiot 
Platinum - Posts: 13,694
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: December 23, 2009 at 10:34 PM / IP Logged  
Does it overheat with just the marker light lit?  
chapeau 
Member - Posts: 4
Member spacespace
Joined: December 22, 2009
Posted: January 14, 2010 at 3:30 PM / IP Logged  
Yes, it overheats with just the marker lights lit.
Sorry for the long delay. It's just been too cold to work in the garage.
i am an idiot 
Platinum - Posts: 13,694
Platinum spaceThis member consistently provides reliable informationspace
Joined: September 21, 2006
Location: Louisiana, United States
Posted: January 17, 2010 at 12:30 AM / IP Logged  
if they are overheating with olny the marker lights lit, and you are sure that you have the dimmer of the 2 elements as the marker lights, it has to be a faulty designed Light housing. 
achebald23 
Member - Posts: 2
Member spacespace
Joined: July 20, 2010
Location: California, United States
Posted: July 26, 2010 at 9:19 PM / IP Logged  
any updates on this? My turn signal light seems to be having the same problem, what was the culprit? Was it the light housing?
achebald23 
Member - Posts: 2
Member spacespace
Joined: July 20, 2010
Location: California, United States
Posted: July 26, 2010 at 11:06 PM / IP Logged  
i think this has something to do with my relay, is there a relay checker tool that i could use to check if my wires are letting current pass through?
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Saturday, November 9, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer