the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

anyone get defrost to work in an integra


Post ReplyPost New Topic
< Prev Topic Next Topic >
riken1 
Member - Posts: 9
Member spacespace
Joined: November 18, 2010
Posted: December 10, 2010 at 2:16 PM / IP Logged  
found the wire that the switch takes to ground when it's pushed. I wired the remote starter defrost output(-) to it. It doesn't work, neither does pushing the button while the car is remote started. When i turn the key to ACC, i can hear the relay energizing when i push the button.
Does something in the defrost circuit have to be energized for this to work?
JWorm 
Platinum - Posts: 2,208
Platinum spacespace
Joined: December 11, 2002
Location: New Hampshire, United States
Posted: December 10, 2010 at 10:04 PM / IP Logged  
Sounds like you need to energize another Accessory wire in the ignition harness with the remote start. Without looking at a chart, I'm thinking either WHITE/ black or yellow wire.
I had a 97 Integra about 10 years ago. I do remember having hooked up the rear defrost to my remote start. Also controlled the moonroof through the remote. It was a fun car to drive.
riken1 
Member - Posts: 9
Member spacespace
Joined: November 18, 2010
Posted: December 10, 2010 at 11:27 PM / IP Logged  
the yellow is for Accessory 1, but there's no mention of an Accessory 2. I don't have any wiring diagrams for the car.
riken1 
Member - Posts: 9
Member spacespace
Joined: November 18, 2010
Posted: December 15, 2010 at 8:05 PM / IP Logged  
this is how i have it wired.
H3/1 IGN 1
H3/2 not used
H3/3 ACC 1
H3/4 STR
H3/5 12+
H3/6 not used
H3/7 not used
H3/8 12+
should the flex relay inputs be used for defrost to work?
scrtcell 
Member - Posts: 22
Member spacespace
Joined: July 11, 2004
Location: United States
Posted: December 15, 2010 at 8:25 PM / IP Logged  
turn the key to the on position and test to see which wire has voltage and make sure that your remote starter is connected to the correct wires
JWorm 
Platinum - Posts: 2,208
Platinum spacespace
Joined: December 11, 2002
Location: New Hampshire, United States
Posted: December 15, 2010 at 8:55 PM / IP Logged  
In the harness you listed above the red, RED / white and RED / black all need to go to constant 12v
riken1 
Member - Posts: 9
Member spacespace
Joined: November 18, 2010
Posted: December 15, 2010 at 9:31 PM / IP Logged  
its a 5301 btw.
so, H3/2 RED / white, fused IGN 2/flex relay input should be 12+? but i don't have IGN2 hooked up. Just IGN1 and ACC1 and both are supplying 12+ when remote started.
riken1 
Member - Posts: 9
Member spacespace
Joined: November 18, 2010
Posted: December 16, 2010 at 3:35 PM / IP Logged  
i found the WHT/BLK wire from the ignition switch that goes to 12+, but it only powers the radio/cigarette lighter.
i think my problem has to do with the Intigrated Control Unit that controls the defrost relay and timer via controlling its ground.

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Monday, October 3, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer