2011 silverado w/ viper 5701 and db all

Home / the12volt's Install Bay / Car Security and Convenience / 2011 silverado w/ viper 5701 and db all (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

flyboy12

Member - Posts: 11

Joined: December 16, 2011

Location: South Dakota, United States

Posted: December 16, 2011 at 7:20 PM / IP Logged

Hey Guys,

I'm a new member to this forum but have been reading it for a while now. I am installing a Viper 5701 remote start/alarm with a DB-ALL bypass on my 2011 Silverado 1500. all went well(doors unlock, lock) until i tried to remote start it. It didnt start, parking lights flashed 7 times. I then went in and programmed the Viper for auto tranny thinking this would fix it, i was wrong.

I double checked all my connections, checked the tranny mode again, the neutral ground and switch, and even tried remote starting with key in ignition. no improvements.

the DBALL has firmware GM6 2.01. it has a RF Loop connected. i installed according to the GM6 install manual.

Im am stumped, Ive been trying to figure it out all day but to no avail. I would really appreciate any ideas!! Thanks

flyboy12

Member - Posts: 11

Joined: December 16, 2011

Location: South Dakota, United States

Posted: December 16, 2011 at 7:23 PM / IP Logged

Oh and I wired it D2D

smokeman1

Platinum - Posts: 1,589

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: December 16, 2011 at 7:28 PM / IP Logged

How did you change it to AUTO? and can you list your wiring from the Viper to the Silverado. And DBALL

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

flyboy12

Member - Posts: 11

Joined: December 16, 2011

Location: South Dakota, United States

Posted: December 16, 2011 at 7:49 PM / IP Logged

smokeman1 wrote:

How did you change it to AUTO? and can you list your wiring from the Viper to the Silverado. And DBALL

I changed it to auto via the valet switch/remote unlock button. I found the directions for that in the download section.

Wiring

VIPER

+Ign Output to Pink wire, BCM lt green plug pin 14

+Acc Output to Brown wire, BCM lt green plug pin 21

-Park Lts to Lt Blue wire, BCM lt green plug pin 8

Neutral safety input(BLACK/ White) and Black Gnd wired to ground

All to Positive(+)

H3/1 PINK (+) IGNITION 1 INPUT/OUTPUT

H3/6 RED IGNITION 1 +12V INPUT (30A FUSED)

H3/9 RED / BLACK ACCESSORY/STARTER RELAY +12V INPUT (30A FUSED)

DBALL

Lt Green Single Wire CAN to OBDII pin 1(green wire)

Violet/Green spliced together with Violet/Brown (R. Codes)

these go to pink/black(resistor code) BCM lt green plug pin 2

RF Loop wrapped around key cylinder

smokeman1

Platinum - Posts: 1,589

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: December 16, 2011 at 10:38 PM / IP Logged

Are you missing the H3/3 wire to Accessory?

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

flyboy12

Member - Posts: 11

Joined: December 16, 2011

Location: South Dakota, United States

Posted: December 16, 2011 at 11:09 PM / IP Logged

smokeman1 wrote:

Are you missing the H3/3 wire to Accessory?

Nope its there. I mentioned it above, "+Acc output to brown" i guess i should have labeled those better.

smokeman1

Platinum - Posts: 1,589

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: December 17, 2011 at 7:30 AM / IP Logged

Does it try to start? As in, does the starter turn the motor over?

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

flyboy12

Member - Posts: 11

Joined: December 16, 2011

Location: South Dakota, United States

Posted: December 17, 2011 at 11:07 AM / IP Logged

nope, nothing but and error tone from the 2 way remote and then a little bit later the park lights flash 7 times. THe manual says to try and manually activate the remote start by pulse grounding H1/10. im going to try today.

flyboy12

Member - Posts: 11

Joined: December 16, 2011

Location: South Dakota, United States

Posted: December 17, 2011 at 12:01 PM / IP Logged

I tried using the H1/10 wire to activate remote start. same thing happens, error tone and then 7 flashes. I then decided to revert all programable settings back to default, including the Tach setting. I then reprogrammed for the auto tranny since manual is default. After that i tried again to get the unit to "learn" the tach, no success. I start the engine and then hold the valet button, the light should come on after 3secs but there is nothing. I then tried to remote start to see what would happen and then its the same old story...

smokeman1

Platinum - Posts: 1,589

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: December 17, 2011 at 3:23 PM / IP Logged

Do you have either H1/6 or H1/8 connected to a door trigger? If not, you should be able to connect H1/8 (Green) to a ground.

Turn the ignition ON, then OFF.

Press and HOLD the valet button until you hear three chirps from the siren, ( 1 chirp, then 2 chirps, then 3 chirps), then release the button.

Now press it ONE TIME and Release, then press it again and HOLD the button down. You should hear ONE chirp from the siren. You are now in the transmission Mode. Press the lock button. You should hear two chirps from the siren. (automatic Mode) Press the lock button again, you should hear one chirp from the siren. (manual Mode). Press the lock button again. Two chirps, (automatic Mode). Release the button wait 30 seconds for the brain to get out of the menus, as noted by a short squeal from the siren. Try to remote start.

If you hear more than two chirps when pressing the lock button, you are in the wrong Menu or Item. Wait for the brain to back out of the menus as noted by a short squeal from the siren, and try again.

I have just tested this procedure on a bench unit (Python 872, same wiring layout as 5701) and it will work.

If I had H1/8 disconnected from a ground, it would not work.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.