2003 yukon remote starter problem

Home / the12volt's Install Bay / Car Security and Convenience / 2003 yukon remote starter problem (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

bigbee

Member - Posts: 11

Joined: January 15, 2012

Location: Ohio, United States

Posted: January 15, 2012 at 11:43 AM / IP Logged

Hi,

I am having some problems with a 2003 GMC Yukon XL.

I have installed an Autopage RS-603 and an Xpresskit DB-ALL module.

The vehicle will attempt so start but shuts down right after cranking. Using the shutdown diagnostic function of the RS-603 it shows 3 slow flashes of the LED. This says it is either a problem with the hood pin switch or the safety shutdown input (brake) or the neutral safety switch.

I have tested these 3 things and they all appear to be working as they should.

The DB-ALL module was flashed for my vehicle and it seems to be working as well. The remote for the remote started locks and unlocks the door so I assume the module is working on the data bus.

I have no idea where to go from here.

I appreciate any and all responses.

Thank you

bigbee

Member - Posts: 11

Joined: January 15, 2012

Location: Ohio, United States

Posted: January 15, 2012 at 11:55 AM / IP Logged

On a side note.

I have verified that I am getting a good tach signal with a digital meter and the RS-603 seems to have it stored.

Thank you

jstruckman

Copper - Posts: 465

Joined: May 03, 2004

Posted: January 15, 2012 at 12:08 PM / IP Logged

Do you have the ground while running wire from the remote start connected to the DBALL. Did you program the DBALL to the vehicle per the instructions of the DBALL. the door locks will work even if this has not been done.

metz35

Copper - Posts: 458

Joined: January 13, 2003

Location: Pennsylvania, United States

Posted: January 15, 2012 at 12:08 PM / IP Logged

Did you hook up the. 2nd ignition?

bigbee

Member - Posts: 11

Joined: January 15, 2012

Location: Ohio, United States

Posted: January 15, 2012 at 12:17 PM / IP Logged

Thanks for the fast replies.

I have the grounded while running wire connected as well as the 2nd ignition wire. I bought the DB ALL programmed already.

jstruckman

Copper - Posts: 465

Joined: May 03, 2004

Posted: January 15, 2012 at 12:25 PM / IP Logged

It is programmed with the software but you need to program it to the vehicle also.

offroadzj

Gold - Posts: 2,043

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: June 03, 2005

Location: New York, United States

Posted: January 15, 2012 at 12:33 PM / IP Logged

Is the neutral safety switch wire grounded? Try starting it with the key in the ignition (not turned) and see if it remote starts. Also, did you use the DB-ALL for the tach signal or run a hard line. From my experience, the DB-ALL tach signal is very unreliable and you are better off running a hardline and programming tach.

Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205

bigbee

Member - Posts: 11

Joined: January 15, 2012

Location: Ohio, United States

Posted: January 15, 2012 at 2:30 PM / IP Logged

I will try programming it to the vehicle and if that sont work I will change the tach wiring around.

Thank you all very much

el ranchero

Copper - Posts: 92

Joined: October 04, 2008

Location: Illinois, United States

Posted: January 17, 2012 at 5:30 PM / IP Logged

i thing dball sucks balls, i do my auto page remote starters with voltage sense, make sure you program to either tach,voltage or timer selection on the auto page r/s

rocker

bigbee

Member - Posts: 11

Joined: January 15, 2012

Location: Ohio, United States

Posted: January 18, 2012 at 10:44 AM / IP Logged

I tried the programming of the DB ALL.

It appears to be programmed.

Next I will change the tach wire hook up.

Thanks for the help, I appreciate it

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.