viper 4704 no start

Home / the12volt's Install Bay / Car Security and Convenience / viper 4704 no start (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

perfecthrasher

Member - Posts: 19

Joined: December 13, 2011

Posted: July 13, 2013 at 10:57 PM / IP Logged

Finally I had time to go back and finish 4704 install on my 2008 Nissan rogue key fob type vehicle. My issue is the starter doesn't turn over checked my grounds etc. What i've found is that there is no power to the starter wire at the ignition plug when I attempt a start. There is approx. 12 volts when I use the key fob what I'm I missing?

Thx

Search for other posts by perfecthrasher

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: July 14, 2013 at 2:55 AM / IP Logged

The heavy duty plug; is there a red, RED / white and RED / black? Are they all connected to a heavy duty (such as ignition loom supply wires) constant?

Has tach been programmed?

perfecthrasher

Member - Posts: 19

Joined: December 13, 2011

Posted: July 14, 2013 at 1:17 PM / IP Logged

I did not connect the RED / white RED / black based on my reading for this vehicle on the forums. I just completed the RED / white RED / black connections redid the tach run and programmed the tach. The vehicle will now turn over (and run) BUT only with the key in the tumbler I gather I have a bypass issue now?

offroadzj

Gold - Posts: 2,043

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: June 03, 2005

Location: New York, United States

Posted: July 14, 2013 at 2:41 PM / IP Logged

Yup. What bypass did you use?

Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205

perfecthrasher

Member - Posts: 19

Joined: December 13, 2011

Posted: July 14, 2013 at 3:14 PM / IP Logged

Idatalink ads-al

mmain1

Member - Posts: 17

Joined: January 03, 2008

Location: Oklahoma, United States

Posted: July 18, 2013 at 9:58 AM / IP Logged

I'm not sure if you are using D2D or W2W. If you are using W2W did you connect the Ground While Running input to the Dark Blue Status Output wire?

perfecthrasher

Member - Posts: 19

Joined: December 13, 2011

Posted: July 18, 2013 at 8:38 PM / IP Logged

I'm doing D2D, I can program the bypass but the led is off during remote start attempt (invalid ground when running status from remote starter). Based on the guide 9473 I connected the solid black lines only so no status output wires have been connected.

kreg357

Platinum - Posts: 7,787

This member has been recognized as an authority in Electrical Theory. Click here for more info.

Joined: January 30, 2009

Location: Pennsylvania, United States

Posted: July 19, 2013 at 6:58 AM / IP Logged

If running D2D mode to a Viper 4704, was / is the iDatalink bypass module flashed with the DBI flavor of firmware ( not the ADS flavor )?

Soldering is fun!

perfecthrasher

Member - Posts: 19

Joined: December 13, 2011

Posted: July 23, 2013 at 8:14 PM / IP Logged

flashed iDatalink 2-way DL-NI4

kreg357

Platinum - Posts: 7,787

Joined: January 30, 2009

Location: Pennsylvania, United States

Posted: July 23, 2013 at 8:50 PM / IP Logged

Still not sure if you have the correct firmware.

DBI-AL(DL)-NI4 for ADS-AL CA bypass module is the correct firmware for D2D with a Viper unit.

ADS-AL(DL)-NI4 for ADS-AL CA bypass module will not work D2D with a Viper unit.

Either will work in W2W mode.

Soldering is fun!

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.