the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

06 ford fusion s w/ crimestopper rs 4 g4


Post ReplyPost New Topic
< Prev Topic Next Topic >
jas51384 
Member - Posts: 32
Member spacespace
Joined: April 26, 2014
Location: Indiana, United States
Posted: April 26, 2014 at 4:56 PM / IP Logged  
Hi all, I'm looking for some help installing the crimestopper RS-4 G4 into my 06 Ford fusion S. The only function I want is the remote start from my OEM key fob. I have found wiring diagrams and the like and have the following connected so far:
12 VOLT CONSTANT BROWN / RED (+)      @ the battery
STARTER      BLUE/WHITE (+)      @ IGNITION SWITCH HARNESS
     
IGNITION 1      WHITE/ ORANGE (+)@ IGNITION SWITCH HARNESS
     
ACCESSORY /HEATER BLOWER 1 PURPLE / GREEN (+)@ IGNITION SWITCH HARNESS
     
PARKING LIGHTS ( - )      GRAY (-)      @ HEADLIGHT SWITCH
POWER LOCK      GRAY / YELLOW (TYPE B)      IN DRIVER KICK PANEL
     
BRAKE      PURPLE / WHITE (+)      @ SWITCH above BRAKE PEDAL
I also have the tach wiring running to a ignition coil.
ok, there are a few wires not connected yet but when I plug in the harnesses to the RS4 "brain" I get relays clicking and the dash lights up along with the "door ajar" ding. The LED is lit dim and it just cycles through this until I unplug it again. I'm afraid I might mess something up if I continue so I'm looking for assistance. I would also like help in continuing the wiring.
Thank you
prdjr165 
Copper - Posts: 293
Copper spacespace
Joined: October 31, 2002
Location: Illinois, United States
Posted: April 26, 2014 at 5:28 PM / IP Logged  
connect the ground wire on the remote start.
jas51384 
Member - Posts: 32
Member spacespace
Joined: April 26, 2014
Location: Indiana, United States
Posted: April 26, 2014 at 5:48 PM / IP Logged  
Sorry I forgot that one. It is connected to a good body ground.
jas51384 
Member - Posts: 32
Member spacespace
Joined: April 26, 2014
Location: Indiana, United States
Posted: April 26, 2014 at 8:10 PM / IP Logged  
So I rechecked the Ground, 12v, ignition, and the account/blower wires they all seem to be correct. So that leads me to believe that its one of the "trigger" wires are incorrect. Also, do I need to have the antenna hooked up?
jas51384 
Member - Posts: 32
Member spacespace
Joined: April 26, 2014
Location: Indiana, United States
Posted: April 26, 2014 at 8:12 PM / IP Logged  
Accessory not account. Autocorrect :)
jas51384 
Member - Posts: 32
Member spacespace
Joined: April 26, 2014
Location: Indiana, United States
Posted: April 30, 2014 at 5:29 AM / IP Logged  
It was the door lock wire. I need to program the unit for the OEM setup first. Thank you for all the replies.
jas51384 
Member - Posts: 32
Member spacespace
Joined: April 26, 2014
Location: Indiana, United States
Posted: April 30, 2014 at 5:36 AM / IP Logged  
With the OEM keyless entry do I need to connect the OEM alarm disarm and rearm wires from the crimestopper? If so, what wires do I use since my wiring diagrams don't specify these two wires?
prdjr165 
Copper - Posts: 293
Copper spacespace
Joined: October 31, 2002
Location: Illinois, United States
Posted: April 30, 2014 at 6:04 AM / IP Logged  
YOU NEED A BYPASS MODULE LIKE A KEY OVERRIDE-ALL
12volts
      WHITE/ red (60A), red (60A)
      +
      SJB, conn. F, pins 1 and 2
     
Starter      blue/white      +      ignition switch, 7 pin plug, pin 7     
Second Starter      N/A                 
Ignition      WHITE/ orange      +      ignition switch, 7 pin plug, pin 1     
Second Ignition      N/A                 
Third Ignition      N/A                 
Accessory      PURPLE / green      +      ignition switch, 7 pin plug, pin 6     
Second Accessory      N/A                 
Keysense      blue/gray      +      ignition switch, 7 pin plug, pin 5     
Power Lock      gray / YELLOW (test with pass sw if equip with mem)      -      driver kick or SJB, conn. C, pin 4     
Power Unlock      PURPLE / gray (test with pass sw if equip with mem)      -      driver kick or SJB, conn. C, pin 10     
Lock Motor      gray/brown      5 wire      driver kick or SJB, conn. E, pin 17     
Unlock Motor      blue/green (without memory)      5 wire      driver kick or SJB, conn. E, pin 27     
Parking Lights+      gray / YELLOW      +      driver kick or SJB, conn. A, pin 31     
Parking Lights-      gray      -      switch or SJB, conn. D, pin 5     
Hazards      BROWN / yellow      -      switch or SJB, conn. D, pin 20     
Turn Signal(L)      blue/green (F); gray/brown (R)      +      SJB, conn. A, pin 21; conn. E, pin 11     
Turn Signal(R)      yellow/purple (F); PURPLE / orange (R)      +      SJB, conn. A, pin 9; conn. E, pin 7     
Reverse Light      GREEN / WHITE      +      driver kick or SJB, conn. E, pin 21     
Door Trigger      GREEN/ purple      - N.C.      driver kick or SJB, conn. C, pin 11     
Dome Supervision      blue      +      driver kick or SJB, conn. E, pin 16     
Trunk/Hatch Pin      yellow/orange      - N.C.      driver kick or SJB, conn. C, pin 6     
Hood Pin      blue/orange      - N.C.      pin switch or SJB, conn. A, pin 27     
Trunk/Hatch Release      brown      -      switch or SJB, conn. D, pin 27     
Power Sliding Door      N/A                 
Factory Alarm Arm      PURPLE / green and YELLOW /GREEN (driver door keypad)      both -      driver kick or SJB, conn. C, pins 16 and 21     
Factory Alarm Disarm      PURPLE / brown (driver door key unlock) (w/o memory)      -      driver kick or SJB, conn. C, pin 5     
Disarm No Unlock      see factory alarm disarm                 
Tachometer      NOT WHITE/ blue      ac      any fuel injector     
Wait to start      N/A                 
Brake Wire      PURPLE / white      +      switch or SJB, conn. A, pin 19     
Parking Brake      gray/blue      -      switch or SJB, conn. C, pin 9     
Horn Trigger      blue/white      -      switch or SJB, conn. B, pin 6     
Memory Seat 1      PURPLE / white      -      Driver Door Module in door, 24 pin plug, pin 4     
Memory Seat 2      yellow      -      Driver Door Module in door, 24 pin plug, pin 16     
Memory Seat 3      N/A      -           
MAKE : FORD | MODEL : FUSION | YEAR : 2006
prdjr165 
Copper - Posts: 293
Copper spacespace
Joined: October 31, 2002
Location: Illinois, United States
Posted: April 30, 2014 at 6:10 AM / IP Logged  
Factory Alarm Arm      PURPLE / green and YELLOW /GREEN (driver door keypad)      both -      driver kick or SJB, conn. C, pins 16 and 21      
Factory Alarm Disarm      PURPLE / brown (driver door key unlock) (w/o memory)      -      driver kick or SJB, conn. C, pin 5
Lock Motor gray/brown   5 wire   driver kick or SJB, conn. E, pin 17 -CONNECT TO GREEN(start activation)WIRE ON RED 3 PIN HARNESS
jas51384 
Member - Posts: 32
Member spacespace
Joined: April 26, 2014
Location: Indiana, United States
Posted: April 30, 2014 at 9:38 AM / IP Logged  
prdjr165 wrote:
Factory Alarm Arm      PURPLE / green and YELLOW /GREEN (driver door keypad)      both -      driver kick or SJB, conn. C, pins 16 and 21      
Factory Alarm Disarm      PURPLE / brown (driver door key unlock) (w/o memory)      -      driver kick or SJB, conn. C, pin 5
Lock Motor gray/brown   5 wire   driver kick or SJB, conn. E, pin 17 -CONNECT TO GREEN(start activation)WIRE ON RED 3 PIN HARNESS
OK thanks. One extra question, I don't have a keypad on the outside. Also, the the gray/brown for the lock motor, will that give me the (-) negative pulse?
Page of 3

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, August 18, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer