the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2001 tacoma, keyless entry


Post ReplyPost New Topic
< Prev Topic Next Topic >
Red97LT1 
Copper - Posts: 57
Copper spacespace
Joined: August 07, 2002
Location: United States
Posted: May 10, 2014 at 10:51 PM / IP Logged  
Going to put a keyless entry setup into the truck. It already has power windows and locks. I have done some looking and I think I have a few things figured out,but need your help on the others.
12v Constant- White >>>>>>>> H1/1
Ignition 12v- BLACK/ Red >>>>>>>> H1/15
Parking light-Green >>>>>>>> H1/10
Door Lock- Gray >>>>>>>>
Door Unlock- Purple >>>>>>>>
200mA second door unlock (H1/2) >>>>>>>> ?????
Door trigger- Green >>>>>>>> ?????
Dome Light Supervision >>>>>>>> ????? ( relay?)
Here's the one I'm installing.
http://http://www.directeddealers.com/manuals/IG/Avital/N2101L_2009-01_web.pdf
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: May 11, 2014 at 3:34 AM / IP Logged  
GREEN/ black to lock grey
Blue/Black to unlock purple
violet and violet/black to a good ground
BROWN / black and WHITE/ black not connected
Green lock trigger to dome light switched ground at dome or plug on fuse box.
Dome supervision not needed, vehicle already has it.
2nd. Unlock you will need relays and knowledge of motor wires, I've dug out a diagram I did previously for Tacoma 2nd. unlock:-
AE5_tacoma.bmp
Red97LT1 
Copper - Posts: 57
Copper spacespace
Joined: August 07, 2002
Location: United States
Posted: May 11, 2014 at 8:29 AM / IP Logged  
Thanks howie.
Red97LT1 
Copper - Posts: 57
Copper spacespace
Joined: August 07, 2002
Location: United States
Posted: May 11, 2014 at 8:49 AM / IP Logged  
Do I need one or two relays? If it's going to be a hassle,I may not use it.
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: May 11, 2014 at 9:17 AM / IP Logged  
None for priority unlock by chance that diagram shows you how.
3prongpaul 
Member - Posts: 4
Member spacespace
Joined: June 25, 2014
Location: Colorado, United States
Posted: June 25, 2014 at 9:52 PM / IP Logged  
I'm trying to connect Avital 2101 to 2001 Tacoma following Howie II drawing but something is not right. Once I get it correct I'll post a known working config so scroll down to later posts before using info in this post.
All I want is one unlock press to unlock drivers door and two unlock presses to unlock both doors.   One press lock to lock both doors.
I would also be satisfied if one unlock press unlocks both doors.
For example, he says H1/7 and H1/9 to good ground but the drawing has H1/7 to ground and H1/9 to 12V+ I'm confused.
Do H1/2 and H1/12 connect to each other as well as Purple wire on 22 pin connector?
Can anyone confirm which wire goes where and if anything should be added/removed from the table below?
Avital2101        Tacoma 2001
H1/1 Red 12V+ all the time
H1/2 Blue        22 pin Purple wire
H1/3 BLACK/ White
H1/4 BLACK/ White
H1/5 GREEN/ Black 22 pin Gray wire
H1/6 WHITE/ Black
H1/7 Violet/Black
H1/8 Blue/Black   12 Pin plug pin 11 Blue cut door side
H1/9 Violet
H1/10 White
H1/11 Black
H1/12 Brown        12 Pin plug pin 11 Blue cut car side
H1/13 Lt GREEN/ Black
H1/14 WHITE/ Blue
H1/15 Yellow       IGN power +
H1/16 Orange
H1/17 BROWN / Black
H1/18 RED / White
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: June 26, 2014 at 1:28 AM / IP Logged  
If something isn't right, what are you doing wrong because I already have one "satisfied customer" see above.
3prongpaul 
Member - Posts: 4
Member spacespace
Joined: June 25, 2014
Location: Colorado, United States
Posted: June 26, 2014 at 7:20 AM / IP Logged  
howie ll wrote:
If something isn't right, what are you doing wrong because I already have one "satisfied customer" see above.
That's what I'm trying to figure out. :)
To me the schematic and text postings don't match so I made a new post to get clarification...hopefully from someone with a known working setup.
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: June 26, 2014 at 8:55 AM / IP Logged  
Apologies, the original post wasn't for priority unlock which is what you want. The drawing IS which explains the seeming contradictions.
Follow the drawing effectively for a 211 thaT MAKES THE LOCK and driver's UNLOCK output wires neg AND THE other doors output 5 wire.
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: June 26, 2014 at 8:57 AM / IP Logged  
H1/12 is the second unlock wire.
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer