the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

Viper 4806 install problem, 2011 Honda Ridgeline RTL


Post ReplyPost New Topic
< Prev Topic Next Topic >
larryrm 
Member - Posts: 18
Member spacespace
Joined: July 15, 2017
Location: Florida, United States
Posted: July 20, 2017 at 6:50 PM / IP Logged Link to Post Post Reply Quote larryrm
correct. But note that pin 3 on the remote starter harness for the 4806 is labeled as Ign.2/Flex.
Then on menu 3 of the programming you reprogram Pin 3 to ACC.2 which goes to the white/black wire.
Other ideas??????
Thank you.
LarryM
n8man 
Member - Posts: 4
Member spacespace
Joined: May 23, 2016
Location: Indiana, United States
Posted: July 21, 2017 at 9:02 AM / IP Logged Link to Post Post Reply Quote n8man
when you check your 12v power wires/fuses. did you test before and after the fuse and not the fuse itself?
larryrm 
Member - Posts: 18
Member spacespace
Joined: July 15, 2017
Location: Florida, United States
Posted: July 21, 2017 at 9:08 AM / IP Logged Link to Post Post Reply Quote larryrm
Checked at the top pins.
LarryM
larryrm 
Member - Posts: 18
Member spacespace
Joined: July 15, 2017
Location: Florida, United States
Posted: July 21, 2017 at 5:10 PM / IP Logged Link to Post Post Reply Quote larryrm
MORE INFO....
If I jumper the pink/white to the pink during crank (the engine starts) and then quickly switch the jumper from red/white to pink after the engine starts, it continues to run. I can then shut it off with the remote.
I have to thus assume that the 4806 is actually supposed to do this automatically but isn't.
Other thoughts????
Thanks.
LarryM
n8man 
Member - Posts: 4
Member spacespace
Joined: May 23, 2016
Location: Indiana, United States
Posted: July 24, 2017 at 9:01 AM / IP Logged Link to Post Post Reply Quote n8man
check the power wires at the 4806 connector. sometimes the fuse holder does not get crimped correctly
larryrm 
Member - Posts: 18
Member spacespace
Joined: July 15, 2017
Location: Florida, United States
Posted: July 24, 2017 at 9:51 AM / IP Logged Link to Post Post Reply Quote larryrm
Power tested to connector terminals plus Rach side of each fuse. All good.
Plus tested continuity on each line. All good.
Only pink wire not putting out voltage as it should for cranking and running.
LarryM
larryrm 
Member - Posts: 18
Member spacespace
Joined: July 15, 2017
Location: Florida, United States
Posted: August 13, 2017 at 4:53 PM / IP Logged Link to Post Post Reply Quote larryrm
All,
thanks for the ideas, however, after a month of screwing with this issue, I replaced the 4806, reprogrammed, and it started right up.
Bad module all along.
LarryM
Page of 3

If you wish to post a reply to this topic, you must first login.
If you are not already registered, you must first register.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, February 22, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer