the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2017 Ford Transit Custom UK Model, Viper 3305V


Post ReplyPost New Topic
< Prev Topic Next Topic >
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: September 30, 2017 at 2:12 PM / IP Logged Link to Post Post Reply Quote howie ll
Yes, yellow to pink/white to IGN at switch or on fuse/relay module or on 17, remove r/hand end cap, prise and 1 X T20 torx you'll see a black plug, yellow/white.
the vuking 
Member - Posts: 48
Member spacespace
Joined: August 23, 2017
Location: United Kingdom
Posted: October 12, 2017 at 6:05 PM / IP Logged Link to Post Post Reply Quote the vuking
I have just been looking at the DB3 all installation notes Howie am I right in thinking because I dont have a remote starter i dont need to use the H3 10 pin black connector pins 1,2,9 and 10 say remote starter
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: October 13, 2017 at 1:34 AM / IP Logged Link to Post Post Reply Quote howie ll
Tell me what they're connected to and you'll get an answer!
the vuking 
Member - Posts: 48
Member spacespace
Joined: August 23, 2017
Location: United Kingdom
Posted: October 13, 2017 at 3:57 AM / IP Logged Link to Post Post Reply Quote the vuking
Pin 1 Green - lock input
Pin 2 Blue - lock unlock input
Pin 9 Pink + ignition input
Pin 10 Blue/White -GWR status input
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: October 13, 2017 at 3:59 AM / IP Logged Link to Post Post Reply Quote howie ll
You need all bar 10 if alarm only.
the vuking 
Member - Posts: 48
Member spacespace
Joined: August 23, 2017
Location: United Kingdom
Posted: October 14, 2017 at 8:49 PM / IP Logged Link to Post Post Reply Quote the vuking
Howie on my van I have had the drivers side lower dash and end panel off and there is a fusebox and what looks like the BCM and also there is the OBD port there. So my question is is this the fusebox that is mentioned in the DB3 installation diagram ? The only reason I question this is because on my last Transit a MK7 there where several fuseboxes and a hidden one behind the glovebox
Thanks
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: October 14, 2017 at 11:10 PM / IP Logged Link to Post Post Reply Quote howie ll
Yes.
the vuking 
Member - Posts: 48
Member spacespace
Joined: August 23, 2017
Location: United Kingdom
Posted: October 15, 2017 at 4:50 AM / IP Logged Link to Post Post Reply Quote the vuking
So I believe im just about on top of this but there are a few connections im not sure about as this is just a alarm install and no R/S seeing the wiring diagram with all the R/S just makes it a little confusing so here are the wires
DB3
Red plug pin 3 Green/White - Door/trunk status output
Red plug pin 6 Gray + Brake output
Red plug pin 5 Violet/White 1 (AC) tach output
Red plug pin 12 Blue/Red - Hood status output
Thanks
howie ll 
Pot Metal - Posts: 16,466
Pot Metal spacespace
Joined: January 09, 2007
Location: United Kingdom
Posted: October 15, 2017 at 6:26 AM / IP Logged Link to Post Post Reply Quote howie ll
Connect all but tach, starter and ACC outputs, if there's a black/white anywhere don't connect. Everything else connect.
the vuking 
Member - Posts: 48
Member spacespace
Joined: August 23, 2017
Location: United Kingdom
Posted: October 15, 2017 at 6:54 AM / IP Logged Link to Post Post Reply Quote the vuking
Thanks for you help Howie so when you say connect all the pin 3 Green/White is a output does this go to the green on the 3305v - door input and as for the pin 6 brake + output I cant see what tht would connec to as the diagram shows it going up to the remote starter module ? then there is the pin 12 - hood status output does this go to the 3305v blue - instant triger input ? and the only black/White I have is the one on the 3305v that is the (-) 200 mA Domelight Supervision Output so im not to use this wire ?
Page of 5

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer