Hello All,
I'm new here and as you probably guessed, I'm in need of some assistance. I'm getting everything together to install a Viper 5606v Alarm/Remote Start into my 2007 Toyota Corolla. I'm the timid type and trying to get all my wires mapped out prior to ripping into this thing. Would it be possible to get some help verifying the wire matchups I've already made and help understanding the ones I've failed to identity?
I'm using the wiring diagram from Bulldog Security, that can be found here:
2007 Toyota Corolla
Below is the wiring info for the device from DEI and I've put what I think is the correct car side wiring in ():
DEI 5606v Manual
Main Harness, White 6-pin connector
1 RED (+)12VDC CONSTANT INPUT ( WHITE @IGNITION SWITCH HARNESS )
2 BLACK (-) CHASSIS GROUND ( FIND A GOOD GROUND )
3 BROWN (+) SIREN OUTPUT ( + WIRE ON SIREN )
4 WHITE/BROWN PARKING LIGHT ISOLATION WIRE - #87a NORMALLY CLOSED of onboard relay
5 WHITE PARKING LIGHT OUTPUT- #30 COMMON of onboard relay
6 ORANGE (-) 500mA (GWA) GROUND WHEN ARMED OUTPUT
Auxiliary/Shutdown/Trigger Harness, White 24-pin connector
1 PINK/WHITE (-) 200mA IGNITION 2/FLEX RELAY OUTPUT
2 BLUE/WHITE (-) 200mA 2ND STATUS/REAR DEFOGGER OUTPUT
3 RED/WHITE (-) 200mA TRUNK RELEASE OUTPUT
4 BLACK/YELLOW (-) 200mA DOME LIGHT OUTPUT
5 DARK BLUE (-) 200mA STATUS OUTPUT
6 WHITE/BLACK (-) 200mA AUX 3 OUTPUT
7 WHITE/VIOLET (-) 200mA AUX 1 OUTPUT
8 ORANGE/BLACK (-) 200mA AUX 4 OUTPUT
9 GRAY (-) HOOD PIN INPUT (N/O OR N/C)
10 BLUE (-) TRUNK PIN/INSTANT TRIGGER INPUT (N/O OR N/C)
11 WHITE/BLUE ACTIVATION INPUT
12 VIOLET/WHITE* TACHOMETER INPUT ( BLACK (AC) @ ECM, FAR RIGHT PLUG, PIN 5, See NOTE #2 )
13 BLACK/WHITE** (-) NEUTRAL SAFETY /PARKING BRAKE/E-BRAKE INPUT
14 GREEN/BLACK (-) 200mA FACTORY ALARM DISARM OUTPUT
15 GREEN* (-) DOOR INPUT (N/O OR N/C)
16 BROWN/BLACK (-) 200mA HORN HONK OUTPUT
17 PINK (-) 200mA IGNITION 1 OUTPUT
18 VIOLET* (+) DOOR INPUT
19 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT
20 BROWN (+) BRAKE SHUTDOWN INPUT ( GREEN/WHITE @ SWITCH ABOVE BRAKE PEDAL )
21 VIOLET/YELLOW (-) 200mA STARTER OUTPUT
22 GRAY/BLACK (-) DIESEL WAIT TO START INPUT
23 ORANGE (-) 200mA ACCESSORY OUTPUT
24 GREEN/WHITE (-) 200mA FACTORY ALARM ARM OUTPUT
* Required connection for manual transmission vehicles.
** Connect this wire to the (-) parking brake wire in the vehicle (see Owners Guide for manual transmission
procedure). Important: NEVER connect 200mA low current outputs directly to a motor or high current device WITHOUT a relay.
Remote Start, White 10-pin heavy gauge connector
1 NC No Connection
2 RED/BLACK (+) FUSED 12V ACCESSORY/STARTER INPUT
3 PINK/BLACK (+) FLEX RELAY INPUT #87a key side (if required) of FLEX RELAY
4 PINK/WHITE (+) IGNITION 2 / FLEX RELAY OUTPUT #30 of FLEX RELAY
5 RED (+) FUSED 12V IGNITION 1 INPUT
6 GREEN (+) STARTER INPUT (KEY SIDE OF THE STARTER DISABLE) ( RED (+) @ IGNITION SWITCH HARNESS )
7 VIOLET (+) STARTER OUTPUT (CAR SIDE OF THE STARTER DISABLE) ( RED (+) @ IGNITION SWITCH HARNESS )
8 ORANGE (+) ACCESSORY OUTPUT
9 RED/WHITE (+) FUSED 12V IGNITION 2 / FLEX RELAY INPUT 87
10 PINK (+) IGNITION 1 INPUT/OUTPUT
Door Lock, 3-pin connector
1 BLUE (-) 500mA UNLOCK OUTPUT ( BLUE/YELLOW @DRIVER KICK, 10 PIN PLUG )
2 EMPTY NOT USED
3 GREEN (-) 500mA LOCK OUTPUT ( GREEN @ DRIVER KICK, 10 PIN PLUG )
Thank you for any assistance you're willing to provide.
Kindest Regards,
Craig