the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2011 Ford Ranger, Viper 5706v


Post ReplyPost New Topic
< Prev Topic Next Topic >
partridgebrad 
Member - Posts: 29
Member spacespace
Joined: April 24, 2020
Location: Ohio, United States
Posted: September 28, 2021 at 9:29 PM / IP Logged  
Alright by any chance could I get a wire by wire connection template for my 2011 ford ranger sport with the viper 5906v. Automatic transmission, power doors and locks with Keyless Entry only. I think I fried the viper brain unit. It is constant blue on the LED all the time and yes it is not in valet mode. Doors lock, door trigger works, lights flash. And I can program. But no remote start and the LED is on constantly. I'd appreciate the help
Brad Partridge
kreg357 
Platinum - Posts: 7,529
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: New York, United States
Posted: September 29, 2021 at 6:45 PM / IP Logged  
Considering the issues you've encountered, this is a big ask of questionable value.
If truck has any possible issues these should be cured before adding an aftermarket system.
You have also noted several discrepancies between the available wire listings from a couple of manufacturers and your particular vehicle.
I believe 2011 was the last year of production for that model so I doubt they spent any money to make changes or updates.
The below info is supplied using data from quality sources but as most installers will admit, each and every wire must be verified with a Digital Multi Meter.
This wire verification is even more important due to the discrepancies noted so far.
Main Harness, 6-pin connector
1 RED (+)12VDC CONSTANT INPUT................................Red (common 40A) (+).........@ Ignition Switch, gray 13 pin plug, pin 2
2 BLACK (-) CHASSIS GROUND...................................Chassis Ground
3 BROWN (+) SIREN OUTPUT.....................................Kit supplied Siren
4 WHITE/BROWN PARKING LIGHT ISOLATION WIRE - PIN 87a.........not used
5 WHITE PARKING LIGHT OUTPUT.....Set Jumper to +)............BLUE/WHITE (+)...............IN DRIVERS KICK or SJB, PLUG (A), PIN 11
6 ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT..................not used
Door Lock, 3-pin connector
1 BLUE (-) 500mA UNLOCK OUTPUT...........PURPLE/GRAY (TYPE B)     IN DRIVERS KICK or SJB, PLUG (B), PIN 26
2 EMPTY NOT USED
3 GREEN (-) 500mA LOCK OUTPUT............GRAY/YELLOW (TYPE B)     IN DRIVERS KICK or SJB, PLUG (B), PIN 27
Remote Start, 10-pin heavy gauge connector
1 NC No Connection
2 RED/BLACK (+) FUSED 12V ACC/STARTER INPUT.............Red (x2) (common 40A) (+)......@ Ignition Switch, gray 13 pin plug, pin 7
3 PINK/BLACK (+) FLEX RELAY INPUT 87A FLEX RELAY........not used
4 PINK/WHITE (+) IGNITION 2 / FLEX RELAY OUTPUT.........Violet/Green (+)..Set to ACC2..@ Ignition Switch, gray 13 pin plug, pin 3
5 RED (+) FUSED 12V IGNITION 1 INPUT....................Red (x2) (common 40A) (+)......@ Ignition Switch, gray 13 pin plug, pin 9
6 GREEN (+) STARTER INPUT (KEY SIDE)....................Blue/White (+).....@ Ignition Switch, gray 13 pin plug, pin 5 \
7 VIOLET (+) STARTER OUTPUT (CAR SIDE)..................Blue/White (+).....@ Ignition Switch, gray 13 pin plug, pin 5 / cut wire
8 ORANGE (+) ACCESSORY OUTPUT...........................Brown/Yellow (+)...@ Ignition Switch, gray 13 pin plug, pin 8
9 RED/WHITE (+) FUSED 12V IGNITION 2 / Flex Relay.......Red (common 40A) (+).........@ Ignition Switch, gray 13 pin plug, pin 2
10 PINK (+) IGNITION 1 INPUT/OUTPUT.....................White/Orange (+)....@ Ignition Switch, gray 13 pin plug, pin 1
Auxiliary/Shutdown/Trigger Harness, 24-pin connector
1 PNK/WHITE (-) 200mA Ignition 2/Flex OUTPUT..................not used
2 BLUE/WHITE (-) 200mA 2ND STATUS /REAR DEFOGGER OUTPUT.......not used
3 RED/WHITE (-) 200mA TRUNK RELEASE OUTPUT....................not used
4 BLACK/YELLOW (-) 200mA DOME LIGHT OUTPUT....................not used
5 DARK BLUE (-) 200mA STATUS OUTPUT...........................to "key-in-the-box" Ground When Running Input
6 WHITE/BLACK (-) 200mA AUX 3 OUTPUT..........................not used
7 WHITE/VIOLET (-) 200mA AUX 1 OUTPUT.........................not used
8 ORANGE/BLACK (-) 200mA AUX 4 OUTPUT.........................not used
9 GRAY (-) HOOD PIN INPUT (NC OR NO)..........................to Kit supplied Hood Pin switch
10 BLUE (-) TRUNK PIN/INSTANT TRIGGER INPUT (N/C OR N/O)......not used
11 WHITE/BLUE ACTIVATION INPUT................................not used
12 VIOLET/WHITE TACHOMETER INPUT..............................grn/blu, gry/yel, pur/gry, yel/org, brn, or grn/wh (AC)....@ any fuel injector, black 2 pin plug, pin 1
13 BLACK/WHITE (-) NEUTRAL SAFETY /PARKING BRAKE INPUT........Chassis Ground if vehicle has Auto Trans
14 GREEN/BLACK (-) 200mA FACTORY ALARM DISARM OUTPUT..........not used
15 GREEN* (-) DOOR INPUT......................................not used
16 BROWN/BLACK (-) 200mA HORN HONK OUTPUT.....................not used - Siren install
17 PINK (-) 200mA IGNITION 1 OUTPUT...........................not used
18 VIOLET (+) DOOR INPUT........Dome Light....................YELLOW\GRAY (+)......SJB BLACK 32 PIN CONN, PIN 8
19 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT........................not used
20 BROWN (+) BRAKE SHUTDOWN INPUT.............................VIOLET\WHITE (+)....@ BRAKE SWITCH
21 VIOLET/YELLOW (-) 200mA STARTER OUTPUT.....................not used
22 GRAY/BLACK (-) DIESEL WAIT TO START INPUT..................not used
23 ORANGE (-) 200mA ACCESSORY OUTPUT..........................not used
24 GREEN/WHITE (-) 200mA FACTORY ALARM ARM OUTPUT.............not used
You can go directly to the battery for the four Viper +12V fused inputs.
As mentioned, the Viper will need some changes to work. These include setting the Transmission Mode, Engine Checking Mode and the Flex Relay Function. The Viper internal Parking Light Fuse/Jumper must be set to (+).
Additionally, you must successfully perform a Tach Learn. Running in Tach Mode is preferred in cold climates.
If you encounter a R/S problem, place a working ignition key into the ignition cylinder but do not turn it. This will allow the key to provide the transponder chip info if the "key-in-the-box" module is not working or installed properly.
Tests must be run to verify that the Viper alarm will trigger if any door or the hood is opened. Test to ensure the remote started engine will shut down if the hood is opened or the Brake pedal is depressed.
Mentioned in an earlier post was info on how to use the four individual door triggers as the Vipers (-) Door Trigger input. This requires a separate Omega AU-NCT module. The trucks (+) Dome Light signal should work.
Here is a link to the Fortin EVO-One install guide for your truck.
https://cdn02.fortin.ca/download/86441/evo-one_ig_reg_bi_for-ranger_2007-2012_a_86441.pdf
Page 3 shows the vehicle connectors and wire colors for most of the needed wires. Nothing is shown for the Alarm needs of your Viper system, like door pins, etc.
Soldering is fun!
partridgebrad 
Member - Posts: 29
Member spacespace
Joined: April 24, 2020
Location: Ohio, United States
Posted: September 30, 2021 at 6:39 PM / IP Logged  
Well I have no one to blame but myself. I followed your instructions to the T. The main thing I had to switch was the negative- door trigger wire which I had connected. It knew when the drivers door was ajar. If armed it would tell me if I had it left open and if I armed the vehicle and opened the door it triggered the alarm. I connected the positive dome light wire to the grey/yellow. Now I have no domelight only on the driver's door ajar. The rest work fine. The system does not know when a door is ajar. Remote start attempts with an error message and the blue led is constantly and it IS NOT IN VALET MODE. I think its fried. I have a PYTHON remote start alarm on the way so Ill try it again. I installed an AVITAL about 8 years ago and had no problems ever. It just recently gave out and that's why I purchased this VIPER. My trucks electrical system is fine. Starts. Everything works so I'm happy for now. This install has been a pain in the butt. I appreciate your help though. Take care.
Brad Partridge
partridgebrad 
Member - Posts: 29
Member spacespace
Joined: April 24, 2020
Location: Ohio, United States
Posted: September 30, 2021 at 6:41 PM / IP Logged  
Oh and I forgot. Due to the door trigger programming is impossible due to you need the door ajar to due any programming
Brad Partridge
kreg357 
Platinum - Posts: 7,529
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: New York, United States
Posted: September 30, 2021 at 7:14 PM / IP Logged  
"I connected the positive dome light wire to the grey/yellow."
I'm thinking this is a typo and should be Yellow/Grey. One listing* shows the wire at Pin 8 as Green/Blue. Either way it should be very easy to test as it should go to +12V only when the Dome Light is ON.
Well, you could try this for the door trigger input so you can get into programming mode.
Disconnect both (+) and (-) Door Trigger wires. Strip off 1/4" of the (-) Door Trigger wire. Use a jumper wire with alligator clips on both ends. Connect one end to the (-) Door Trigger wire.
To get into Viper Programming Mode, connect the other end of the jumper wire to solid vehicle chassis ground as the first step, then turn the IGN ON then OFF, etc, etc.
In the Viper programming, you can set Menu 1, Feature 13 to Option 2** and connect the (-) Door Trigger wire to just one of the four vehicle N.C. door trigger wires. This will allow the Viper Alarm to work and get you into Programming Mode but only alarm/monitor that one door. You can't do this to more than one door at a time.
*Dome Light......green/blue (+)........@ SJB in passenger kick, black 32 pin plug (C), pin 8
**This tells the Viper that the vehicles' door trigger wire is a N.C. signal.
Soldering is fun!
partridgebrad 
Member - Posts: 29
Member spacespace
Joined: April 24, 2020
Location: Ohio, United States
Posted: October 03, 2021 at 7:36 AM / IP Logged  
My dome light will not come on my 2011 Ford ranger with my drivers door only I installed the viper 5906v and have this problem along with everytime I arm the system I get the warning door open. Any answers?
Brad Partridge
kreg357 
Platinum - Posts: 7,529
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: New York, United States
Posted: October 03, 2021 at 8:26 AM / IP Logged  
What do you have connected on the Viper as far as the two Door Trigger wires and the Dome Light supervision wire?
Used? Not Used? Where connected to in the truck?
4 BLACK/YELLOW (-) 200mA DOME LIGHT OUTPUT
15 GREEN (-) DOOR INPUT
18 VIOLET (+) DOOR INPUT
Also noticed your other post about the Python 5706 system. Do you have the Python system yet? Did you compare the Python Install guide to the Viper 5706 Install Guide?
I'm not a big DEI user but I believe that the only difference between those two systems are the remotes and the antenna. The connectors, wires and programming should be the same.
Soldering is fun!
partridgebrad 
Member - Posts: 29
Member spacespace
Joined: April 24, 2020
Location: Ohio, United States
Posted: October 03, 2021 at 9:02 AM / IP Logged  
I was told not to use the black/yellow(-) dome light output or the green(-) door input wire. Instead use violet(+)door input and connect to yellow/gray(+) sjb black 32 pin connector pin 8.then it was switched to green/blue(+) from same source.
Brad Partridge
kreg357 
Platinum - Posts: 7,529
Platinum spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: January 30, 2009
Location: New York, United States
Posted: October 03, 2021 at 11:47 AM / IP Logged  
So which wire at the SJB actually tested as a (+) Dome Light wire? There was some conflicting info from the various sources.
Nothing is connected to any of the trucks four actual door trigger wires, correct?.
Think at this point I would disconnect the Viper (+) Door trigger input wire and see if the the trucks dome light and Driver door works OK. If not then troubleshoot that issue.
As mentioned previously, you can get the Viper into Programming Mode by using the (-) Door Trigger Input wire going to chassis ground to simulate a N.O. door open status. Then change Menu 1, Feature 13 to Option 2. Next locate, test and verify the passenger front door trigger and connect the Vioer (-) Door trigger input wire to that. You will only be monitoring that one door with the Viper Alarm but at least you can test it and get into Programming Mode.
Soldering is fun!
partridgebrad 
Member - Posts: 29
Member spacespace
Joined: April 24, 2020
Location: Ohio, United States
Posted: October 03, 2021 at 4:59 PM / IP Logged  
Well I pulled everything out considering the Python will be here soon. My only issue is the dome light does not come on with the drivers door only.works on all other 3. I will have to tackle this before I install anything. What a headache. Thanks for your help though. Much appreciated ***** Admin Edit: Topic closed. See new topic.
Brad Partridge
Page of 2

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Wednesday, December 1, 2021 • Copyright © 1999-2021 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer