2001 honda odyssey, taplock install

Home / the12volt's Install Bay / Car Security and Convenience / 2001 honda odyssey, taplock install (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

bbmon

Member - Posts: 7

Joined: June 25, 2004

Location: United States

Posted: August 24, 2004 at 11:11 AM / IP Logged

I just bought this little gadget called taplock (please see http://www.taplock.com) which unlocks doors with your security taps on the window.. I've installed it and works great but my question is how do I wire it with my factory alarm disarm wire ? because right now it unlocks doors but the factory alarm goes off...

I have 2001 honda odyssey exL which has a factory disarm wire that requirs a -ve pluse.

The wiring for the taplock is as follows:

1. Red wire to a "continuously 'on'" source of + 12 volt fused.

2. Black wire to ground. This may be any metal part of the car frame.

3. Orange wire to the "ignition-on" +12 volt fused connection at the ignition switch.

This wire can be omitted if the Receiver Module (i.e.RED light ) is hidden from view.

4. Blue and RED fused wire to the "uplock" wire for actuating the lock.

5. Blue # 2 wire can either go to Ground or to +12 volt, depending if a Ground Pulse or Negative Pulse needs to be sent to the door uplock solenoid.

I'll appreciate if anyone gives me any suggestions for this to work. Thanks...

Back to Top

SnomanF150

Silver - Posts: 269

Joined: September 19, 2002

Location: United States

Posted: August 24, 2004 at 11:44 AM / IP Logged

You should be able to take whichever wire sends a neg. output when you tap on the car and connect it to the factory alarm disarm wire. You may need to diode isolate it.

Back to Top

bbmon

Member - Posts: 7

Joined: June 25, 2004

Location: United States

Posted: August 24, 2004 at 1:02 PM / IP Logged

SnomanF150, can you be more specific... do you mean from above taplock wires I take the blue #2 that gies to ground and connect with factory disarm wire along and the ground both.? I'm not familiar with how to use diode and what type of diode to use and how to use it..

Back to Top

draasch

Gold - Posts: 2,172

Joined: February 07, 2003

Location: Florida, United States

Posted: August 24, 2004 at 8:07 PM / IP Logged

take this wire:Power Unlock GREEN/ RED (-) DASH FUSE/RELAY BLOCK

and put a diode in-line and run a wire from the above wire to this wire:OEM Alarm Disarm BLUE (-) ON EX 3 PIN GRAY CONN. BELOW COLUMN** ** On LX At Drivers Door Multiplex Control Unit In Drivers Door.

when you unlock the doors, it will send the same pulse to the disarm wire......

Good Luck

David

Ace Security

813-376-9778

Tampa

Donate to the 12volt

Back to Top

bbmon

Member - Posts: 7

Joined: June 25, 2004

Location: United States

Posted: August 25, 2004 at 2:08 PM / IP Logged

thanks for all replies... It worked out well... put a diode between factory disarm and taplock wire that goes to door unlock.. works great.

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

2001 honda odyssey, taplock install

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.