the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

rs cuts off when door is open


Post ReplyPost New Topic
< Prev Topic Next Topic >
mpathy 
Member - Posts: 47
Member spacespace
Joined: October 05, 2004
Posted: November 08, 2004 at 9:25 PM / IP Logged  

   I have a seperate hood pin wire . The door trigger is a seperate zone . Now I understand what you are saying But my thing is that if that is the case it should stay off . This unit is starting right back up after shutting down.

I am not sure what to do anymore....

jrilla 
Gold - Posts: 1,498
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: November 19, 2002
Location: North Dakota, United States
Posted: November 09, 2004 at 10:55 AM / IP Logged  
How do you have the door triggers connected to the alarm? My notes show seperate wires for each door and tailgate making that 5 wires you need to connect to. If this is how you have it set up, then I have a diagram that shows you need to cut ech wire and install a diode with the band facing away from the BCM. Then you need to make a connection on the door side of each wire and install a diode on each with the band facing the alarm, then connect all 5 wires to your alarm unit.
Before i saw that diagram I was going to suggect using a relay to isolate the door triggers. Like this:
Pin 85 gets connected to all door trigger wires (diode isolate all five wires though still)
Pin 86 12v+ constant
Pin 30 chassis ground (fused)
Pin 87 goes to the alarm door triggers input wire
J Rilla
Owner/Installer
mpathy 
Member - Posts: 47
Member spacespace
Joined: October 05, 2004
Posted: November 09, 2004 at 2:46 PM / IP Logged  

  No I only have one wire hooked up which seems to work for all the doors when I tested it , 

What you are talking about will that this stop my issue with the RS cutting out the restating when door is open?

jrilla 
Gold - Posts: 1,498
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: November 19, 2002
Location: North Dakota, United States
Posted: November 09, 2004 at 4:48 PM / IP Logged  
It might. Which wire and where are you connected?
J Rilla
Owner/Installer
mpathy 
Member - Posts: 47
Member spacespace
Joined: October 05, 2004
Posted: November 09, 2004 at 5:15 PM / IP Logged  

Dome  Lights/Superv:   BROWN / L GREEN (-)  AT BODY CONTROL MODULE ***

This is what I connected to . Here is the link to the wire codes I have

http://www.designtech-intl.com/Content/techsupport/wirecolors/VehicleDetail?modelID=355

jrilla 
Gold - Posts: 1,498
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: November 19, 2002
Location: North Dakota, United States
Posted: November 09, 2004 at 5:27 PM / IP Logged  
Ok, what I would try first (if youhave an extra relay handy) is to isolate that wire from the alarm by setting up a relay like I mentioned above. If that doesn't work then you could try cutting the door trigger wire on the vehicle and installing a diode with the band facing away from theh BCM. Then connecting the alarm wire to the side the band is on.
Keep us updated
J Rilla
Owner/Installer
mpathy 
Member - Posts: 47
Member spacespace
Joined: October 05, 2004
Posted: November 09, 2004 at 6:48 PM / IP Logged  

  I will try that and keep you posted . Thanks for the help.

mpathy 
Member - Posts: 47
Member spacespace
Joined: October 05, 2004
Posted: November 09, 2004 at 6:50 PM / IP Logged  

  I have a question. With the relay setup will that give me a - output?

jrilla 
Gold - Posts: 1,498
Gold spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: November 19, 2002
Location: North Dakota, United States
Posted: November 09, 2004 at 7:07 PM / IP Logged  
No, the door oprning triggers the relay which connects the alarm input wire to ground and tells the alarm the door was opened. Since the door trigger wire goes to ground when the door opens, we can do the same by connecting the alrm wire to ground and use the door trigger wire as the trigger for the relay.
J Rilla
Owner/Installer
mpathy 
Member - Posts: 47
Member spacespace
Joined: October 05, 2004
Posted: November 09, 2004 at 8:08 PM / IP Logged  
I see .. Thank you . I will let you know what happens
Page of 2

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, May 16, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer