Viper 791xv

Home / the12volt's Install Bay / Car Security and Convenience / Viper 791xv (

Topic Closed)

Welcome Guest :)

Members

< Prev Topic Next Topic >

2001svt

Member - Posts: 3

Joined: April 14, 2005

Location: United States

Posted: April 20, 2005 at 11:42 AM / IP Logged

Hello,

I was looking over the installatin guide on the 791 xv. I'm confused on the H1/3 WHITE/ blue remote start wire. Where do I connect it? I havent did an alarm install for about 7yrs. I'm a little rusty.

Thanks

Montrealler

Copper - Posts: 155

Joined: October 05, 2002

Location: Canada

Posted: April 20, 2005 at 7:38 PM / IP Logged

http://www.directechs.com/guides/manuals/ig/viper/N564V_01-05.pdf

As seen on page 18 of their guide if you did not change the factory setings if this wire receive 2 consecutive pulse of ground the remote start will engage...

Glade to diserve you !!!!!!!!!!!!11

WD-40!

2001svt

Member - Posts: 3

Joined: April 14, 2005

Location: United States

Posted: April 21, 2005 at 12:27 PM / IP Logged

Leaving the stock settings alone. I don't need to hook up this wire. Right?

Smoke Signals

Member - Posts: 12

Joined: March 29, 2005

Location: United States

Posted: April 21, 2005 at 2:41 PM / IP Logged

This wire is so you could hook up a momentary switch inside the car to activate the remote start. (Never understood that since if you were in the car you could use the key).

If you want this option hook one side of the switch to this H1/3 wire, the other side to ground. Push the button twice and the remote start should activate.

2001svt

Member - Posts: 3

Joined: April 14, 2005

Location: United States

Posted: April 21, 2005 at 3:02 PM / IP Logged

Thanks for the info. I was confused on that one!

Calgarysouth

Member - Posts: 39

Joined: April 19, 2005

Location: Canada

Posted: April 21, 2005 at 3:38 PM / IP Logged

smoke signals.....

you are right, there is no point of having a button inside the car to start the car with.....but you could use it for a remote start timer or some other device.

nava94

Silver - Posts: 296

Joined: February 28, 2004

Location: United States

Posted: April 23, 2005 at 12:53 PM / IP Logged

i don't see the point of that either? DEI please explain.

metaverse

Copper - Posts: 210

Joined: June 13, 2002

Location: United States

Posted: April 23, 2005 at 11:40 PM / IP Logged

That wire is so you can 1) test remote start while you are installing/troubleshooting it to see if it (remote start) works. 2) to tie it into an existing system that already has an alarm/keyless entry so you don't have to carry 2 remotes. For e.g. you have a keyless entry unit that can emit pulses on a different channel which you can tie into this wire to make it start. You can also do 3) which is start button. 4) You an also tie it into a door keypad.. There are multiple uses for it..or, just don't use it..

nava94

Silver - Posts: 296

Joined: February 28, 2004

Location: United States

Posted: April 23, 2005 at 11:51 PM / IP Logged

that's kool and the gang.now that makes sense.thankz for the response metaverse.

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Viper 791xv

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.