DEI 530T on '01 honda accord

Home / the12volt's Install Bay / Car Security and Convenience / DEI 530T on '01 honda accord (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

xone

Member - Posts: 25

Joined: May 21, 2005

Location: United States

Posted: May 23, 2005 at 10:30 AM / IP Logged

Hey i was wondering if anyone out there new how to install DEI's 530T window roll up module? Ive got it working but for some reason my windows go down 2 inches and stop. The drivers door has "one touch" but i cant seem to find the relays that make it work. Ive hooked up right after the window motor and at the switch but they never roll all the way down. If anyone has some suggestions i would really apreciate it.

daze

Copper - Posts: 112

Joined: December 02, 2004

Posted: May 23, 2005 at 11:22 AM / IP Logged

when it only rolls a few inches, are you using the switch or are you using a channel output ?

if its the output that is doing it then the pulse may not be the right kind. if you pulse the 530t then it vents (2 inches) if you have a longer ground... it will roll all the way down.

if its from the switch, then it will be your resistance settings (there is a panel) there are 4 little white switches, read the manual on how to adjust

xone

Member - Posts: 25

Joined: May 21, 2005

Location: United States

Posted: May 23, 2005 at 11:33 AM / IP Logged

so setting the pin switces will fix that? i thought they were for adjusting the sensitivity of the movement.

daze

Copper - Posts: 112

Joined: December 02, 2004

Posted: May 23, 2005 at 12:38 PM / IP Logged

no the switches adjust the resistance. (how it can tell if the window is in motion or stoped). if they are not set right.. it can cause the same problem you are having. if the drivers window and the passanger window are acting the same then it has nothing to do with the one touch. (if you only have drivers one touch) the 530T should allow you to have one touch for all windows that it is hooked up to.... its a little tricky getting use to !

xone

Member - Posts: 25

Joined: May 21, 2005

Location: United States

Posted: May 23, 2005 at 2:18 PM / IP Logged

yea both windows do the same thing. as a matter of fact the passenger window is delayed from the driver window. do you think the switches could be causing that too? I ran the window 2 wires from the 530T to the passenger door so that i could have the one touch for the both doors (man that was a bich! DEI 530T on '01 honda accord -- posted image.

DEI 530T on '01 honda accord -- posted image.

). I apreciate the info daze, i'll see if i can play around with the switches let me know wat you think about the passenger delay.

xone

Member - Posts: 25

Joined: May 21, 2005

Location: United States

Posted: May 23, 2005 at 10:41 PM / IP Logged

damn this things pissing me off! I cant get it to work right! I tried every combination of the dip switches and nothing works. Has anyone installed the 530T in an 2001 acord? Is there anything special I need to know about the windows and the one touch?

Teamrf

Gold - Posts: 1,031

Joined: January 13, 2004

Location: United States

Posted: May 23, 2005 at 10:53 PM / IP Logged

I have the 530T on my car which is a 01 Accord Coupe...what is your question?

~The Rookie~

Rookie of the year that is...

Don't let the smoke out of your equiptment..it doesn't go back in.

Teamrf

Gold - Posts: 1,031

Joined: January 13, 2004

Location: United States

Posted: May 23, 2005 at 10:55 PM / IP Logged

I ran 12awg wires over to the pass. window. And went to the switch in the drivers switch on the driver's side.

~The Rookie~

Rookie of the year that is...

Don't let the smoke out of your equiptment..it doesn't go back in.

xone

Member - Posts: 25

Joined: May 21, 2005

Location: United States

Posted: May 23, 2005 at 11:01 PM / IP Logged

coo!

well i hooked up to both doors from the 530T, and then to my alarm aux outputs. everything worked fine exept when i hit the aux 1 button on my remote the windows would go down and stop about two inches. when rolling down the passenger door was delayed from the driver door but when rolling up they were both in sinc. but would only roll up inch by inch. I re set all the dip switches to every possible combination and still no luck. am i doing something wrong? I thought i needed to bypass the one touch but the relays are in the switch apperantly. How did you install it?

xone

Member - Posts: 25

Joined: May 21, 2005

Location: United States

Posted: May 23, 2005 at 11:12 PM / IP Logged

hey teamrf nice rims i been wanting to get some bigger wheels on my accord but was afraid they wouldnt look right but yours looks prety clean. I like the crhome ones tho.

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.