remote start in 5 speed

Home / the12volt's Install Bay / Car Security and Convenience / remote start in 5 speed (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

godshandkiller

Member - Posts: 15

Joined: June 29, 2005

Location: United States

Posted: August 10, 2005 at 11:04 PM / IP Logged

i have a 2000 mustang gt 5 speed with a python 881 xp that i installed.how can i make theremote start not work until the emergency brake is on for safety.

Search for other posts by godshandkiller

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: August 11, 2005 at 12:09 AM / IP Logged

DEI Electronics wrote:

IMPORTANT! This product is designed for fuel-injected, automatic transmission vehicles only.

Installing it in a standard transmission vehicle is dangerous and is contrary to its intended use.

Doesn't matter if the park brake is engaged, the car will still lurch forward. Just go and buy a system designed for a manual transmission vehicle

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

adambeazley

Member - Posts: 15

Joined: June 28, 2005

Location: United States

Posted: August 11, 2005 at 12:41 AM / IP Logged

Well this is basically what I did to make a neutral safety switch. Check out the picture

remote start in 5 speed -- posted image.

As you can see in the picture I have placed two springs on either side of the stick shift. Then I wrapped the actual stick with electrical tape and then wrapped a aluminum reflective tape around the electrical tape to isolate it from the metal stick. Now what happens is when the stick is in gear 1, 3 or 5 the back spring doesnt touch the reflecting tape and therefore the ground connection is broken and the car wont start. Now when the stick is in 2nd, 4th or reverse the ground is again broken and the car cant start. You just connect the neutral/parking safety wire from your alarm head unit to one spring and then ground the other spring. As far as materials go I just used some tiny 1/4" brass wood screws to screw into the plastic. Well let me know what you think or if you have any questions.

peace

Adam

xtreme069

Copper - Posts: 67

Joined: June 15, 2004

Location: Australia

Posted: August 12, 2005 at 11:43 PM / IP Logged

directed actually have a neutral saftey switch which is called a rope switch it basically ataches to the shifter and detects movement forward and back when we order them the part no. is a GSRW good luck

I Love This Industry!!

KarTuneMan

Platinum - Posts: 7,056

This member consistently provides reliable information

Joined: December 14, 2004

Location: Isle Of Man

Posted: August 13, 2005 at 3:01 AM / IP Logged

Oh GOD.........here we go again...................

xtreme069

Copper - Posts: 67

Joined: June 15, 2004

Location: Australia

Posted: August 13, 2005 at 5:26 AM / IP Logged

what's the problem? Kartuneman

I Love This Industry!!

KarTuneMan

Platinum - Posts: 7,056

Joined: December 14, 2004

Location: Isle Of Man

Posted: August 13, 2005 at 4:07 PM / IP Logged

Thank you bobk!

shesaidshewas18

Copper - Posts: 96

Joined: September 24, 2004

Location: United States

Posted: August 14, 2005 at 6:46 AM / IP Logged

I think kartuneman is never gonna see the end of these types of posts. Rather than whining, he should just make a post about it, put a link to his thread in his sig, and then everytime he see's a thread with this kind of topic he could just say "ChEcK My SiG yO"

Search for other posts by shesaidshewas18

KarTuneMan

Platinum - Posts: 7,056

Joined: December 14, 2004

Location: Isle Of Man

Posted: August 14, 2005 at 1:49 PM / IP Logged

HERE IT IS.....If it ain't for a manual trans......DON'T ATTEMT TO PUT IT IN. And dont ask US how to jerry rig it remote start in 5 speed -- posted image.

I don't "whine" I just wish that stupidity and ignorance were painful.............

xtreme069

Copper - Posts: 67

Joined: June 15, 2004

Location: Australia

Posted: August 15, 2005 at 7:20 AM / IP Logged

Kartuneman, you must be one of those old guys who thinks he knows all there is to know, all godshandkiller wanted to know was how to make his remote start system safe, he already has the alarm so changing it is out of the question and no matter what you say he's probably going to fit it anyway so instead of telling him he's an idiot maybe give him a safe way of doing it by either telling him to find the neutral safety switch wire on the computer or as i guided him towards the rope switch sure put across your point of view but don't belittle people the forum is for help not hinderence get off your hi horse!!!!!!

Also why would directed sell the rope switch if it wasn't reliable???

As for godshandkiller good luck with your project just remember your starting your car at your own risk and maybe others around you so starting it in a crowded area is probably not a good idea again good luck

I Love This Industry!!

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.