the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2003 Accord Remote Start


Post ReplyPost New Topic
< Prev Topic Next Topic >
aasaro4 
Member - Posts: 13
Member spacespace
Joined: December 29, 2005
Posted: December 29, 2005 at 6:08 PM / IP Logged  

I have a couple questions if anyone can help, Im installing a ultrastart remote starter ....

1. Why is there 2 12 volt input wires ? Do I use them both? Should I hook them both to the constant 12 volt wire?

2.What is the "ground while running/starter kill" wire get hooked up to?

3. There is a 3 pin connector that gets hooked to "ground while running" , "ground output", and "12volt output, where do these get connected to"

4. I also have to install the key transponder bypass, where do the two wires get connected too??

Thanks for any help

Joe Neal 
Copper - Posts: 113
Copper spacespace
Joined: October 15, 2004
Location: United States
Posted: December 29, 2005 at 6:39 PM / IP Logged  

Not sure of the Model Transponder, but usually the wires would hook to:

 12 Volt + Constant
Ground Out while Running from R/S

If your Remote Start 2 - 12 Volt Input Wires, & your vehicle only has One 12 Volt Constant wire at Ignition Switch, then you would hook Both to that.

05gt 
Silver - Posts: 628
Silver spacespace
Joined: October 30, 2005
Location: British Columbia, Canada
Posted: December 29, 2005 at 6:48 PM / IP Logged  

1) yes

2) used for optional starter kill relay, or immbolizer bypass module which you need to be able to remote start

which bypass module are you using

aasaro4 
Member - Posts: 13
Member spacespace
Joined: December 29, 2005
Posted: December 29, 2005 at 7:06 PM / IP Logged  
Its an ultrastart 1355a remote starter and the transponder bypass is an autotran
05gt 
Silver - Posts: 628
Silver spacespace
Joined: October 30, 2005
Location: British Columbia, Canada
Posted: December 29, 2005 at 8:19 PM / IP Logged  

i don't have any experience with that bypass module, so I can't help you

jmacf14 
Copper - Posts: 160
Copper spaceThis member has made a donation to the12volt.com. Click here for more info.spacespace
Joined: December 27, 2005
Location: United States
Posted: December 30, 2005 at 12:15 AM / IP Logged  
 yes you need to hook both of them up    the first supplies 12volts for the ignition, parklight and selectable outputs.  and the second red is for suppliing 12volts for acc. and starter outputs. you can tap both into the same constant 12volt source at the ignition harness. should come with 30amp fuse in each red wire.   hope that helps.
jmacf14
aasaro4 
Member - Posts: 13
Member spacespace
Joined: December 29, 2005
Posted: December 30, 2005 at 7:06 PM / IP Logged  
Okay next question, it says that the wires for the factory alarm arm/disarm are in the "driver door module in door"  where is this at? inside the door? and if so does anyone have a clue how to get to it,  thanks
nyanks03 
Member - Posts: 3
Member spacespace
Joined: September 06, 2003
Location: United States
Posted: December 30, 2005 at 7:18 PM / IP Logged  

Yeah the driver's door module is located inside the door.

-Nyanks03
aasaro4 
Member - Posts: 13
Member spacespace
Joined: December 29, 2005
Posted: December 31, 2005 at 10:47 AM / IP Logged  

Can you be more specific? I took the panal off and I still need some direction, have you seen any pictures on the net of where it is?? Thanks , this is becoming a pain in the ***

snguyen 
Silver - Posts: 281
Silver spacespace
Joined: October 09, 2003
Location: United States
Posted: December 31, 2005 at 12:09 PM / IP Logged  

2003 Accord Remote Start -- posted image.

I drill a small hole in the plug, then I ran it thru the boot of the door.

2003 Accord Remote Start -- posted image.

Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Friday, March 29, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer