AVIC-N1 Part Number Request

Home / the12volt's Install Bay / Mobile Video, GPS, and Navigation / AVIC-N1 Part Number Request (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

mantis971

Member - Posts: 9

Joined: April 11, 2005

Posted: January 18, 2006 at 11:40 AM / IP Logged

He also says "**you want to make your n1 work with the new n2 software but you would like to have it still play movies while driving **". Did he do that for yours to?

snowboarderandy

Member - Posts: 45

Joined: November 24, 2004

Location: United States

Posted: January 18, 2006 at 11:59 AM / IP Logged

He replaced the ribbon cable, stripped gears, motors, and the connections to the removeable faceplate. I have not bought the new 50 series discs yet so I didnt need him to make my N1 work like a N2 without the safety features. Send him an email and he will email you back an estimate.

Thanks,

Andy

twinmax

Member - Posts: 7

Joined: May 22, 2005

Location: United States

Posted: February 04, 2006 at 12:34 PM / IP Logged

Hey afranke have you recieved the part yet? Also how much did it cost?

fearx24

Copper - Posts: 60

Joined: April 22, 2003

Location: United States

Posted: April 05, 2006 at 4:59 PM / IP Logged

I just ordered that part from Pioneer. It cost $38.00 from them.

neal1154@yahoo.

Member - Posts: 14

Joined: March 09, 2006

Posted: April 06, 2006 at 12:11 PM / IP Logged

if you are using the CNP7621 it will break again because it is the same part you need the upgrade part I have been using it for months on units and I have never had one come back

Search for other posts by neal1154@yahoo.

fearx24

Copper - Posts: 60

Joined: April 22, 2003

Location: United States

Posted: April 07, 2006 at 11:21 AM / IP Logged

Ya I got the upgraded part GXX1257

fearx24

Copper - Posts: 60

Joined: April 22, 2003

Location: United States

Posted: April 07, 2006 at 5:46 PM / IP Logged

Need some help though. I installed the new ribbom cable part and everything went fine but when I install the unit the screen comes out but doesnt flip up it just stays out and wont flip up. I can flip it up by hand rotating the gears and it works fine it just doesnt flip up when install. One of the gears has an arrow on it. Does that arrow have to be at a certain starting position. Any Help ASAP would be appreciated.

Thanks

smokenjet

Member - Posts: 15

Joined: April 09, 2006

Location: Florida, United States

Posted: April 09, 2006 at 8:30 PM / IP Logged

Does anyone have the contact information for this guy. I want to see about the N2 software upgrade on my N1 and keep my video going.

Ballerinstaller

Copper - Posts: 58

Joined: May 18, 2005

Location: United States

Posted: April 26, 2006 at 2:59 PM / IP Logged

I had a problem with my N1 where the screen only came out a inch and stop. Found a tiny tear in the flex. Went to order from Pioneer and it has been discontinued. New part number is GXX1257 @ $38.60 +s/h ($12)

Pete

Pioneer Avic-N1

Clarion 300 watt 4 channel amp

PPI PC21400 1400 watt amp

2x JL 12 inch w7's

Polk EX series in factory locations

2000 Impala LS

Baller Installer - Pete D.

Search for other posts by Ballerinstaller

Bigkevin20

Copper - Posts: 84

Joined: May 20, 2003

Location: United States

Posted: April 27, 2006 at 1:53 PM / IP Logged

the hack on the N1 works I sent mine to him

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.