93 mazda 929, bulldog 62I

Home / the12volt's Install Bay / Car Security and Convenience / 93 mazda 929, bulldog 62I (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

Installer_mss

Copper - Posts: 221

This member has made a donation to the12volt.com. Click here for more info.

Joined: February 14, 2005

Location: United States

Posted: August 23, 2006 at 12:42 AM / IP Logged

it's the ground. check the brains ground and the siren ground. make sure the paint, dirt, etc. is removed to the bare metal where you ground both grounds and make sure the screw/bolt is tight but not stripped out. but it is definitely the ground

rock1

Copper - Posts: 120

Joined: April 06, 2005

Posted: August 23, 2006 at 8:35 AM / IP Logged

I will check.

how do you know if the siren is bad?

thepencil

Gold - Posts: 1,526

Joined: December 16, 2002

Location: Canada

Posted: August 23, 2006 at 8:54 AM / IP Logged

"how do you know if the siren is bad?"

When there is no sound coming out of it. 93 mazda 929, bulldog 62I - Page 3 -- posted image.

Very easily, applying full + and - to the siren and seeing how it sound is a very good indication of the condition of your siren.

Be careful whose advice you buy, but be patient with those who supply it. 93 mazda 929, bulldog 62I - Page 3 -- posted image.

rock1

Copper - Posts: 120

Joined: April 06, 2005

Posted: August 23, 2006 at 9:34 AM / IP Logged

I checked the siren and the ground was clean the siren has some water and after draining it out the siren is loud again.

xtremej

Gold - Posts: 1,440

Joined: February 24, 2006

Location: United States

Posted: August 23, 2006 at 9:36 AM / IP Logged

Depends if its current sensing or not. It goes off when you open it because its probably wired off the door triggers, therefore detecting that the door is open.

rock1

Copper - Posts: 120

Joined: April 06, 2005

Posted: August 23, 2006 at 11:34 AM / IP Logged

but on my car it says the dome light is the door trigger.

92 mazda 929

Cameronjc

Member - Posts: 29

Joined: February 06, 2004

Posted: August 23, 2006 at 2:54 PM / IP Logged

I think your a bit confused.

The doors are wiried to your dome light, when your doors open, the light turns on. The alarm trigger is connected to the switch on the doors, so that when the doors open, the alarm will know and be triggered.

The wire the alarm connects on the doors is the same one that activates the dome light.

The wiring your dome light switch uses to turn the dome light is different and will not cause the alarm to sound.

rock1

Copper - Posts: 120

Joined: April 06, 2005

Posted: August 23, 2006 at 3:24 PM / IP Logged

so if you open the door and the alarm goes off and the light comes on thats ok but if thats the wire that makes the alarm goes off how come it does not sound off when I press the door triger button down intill the dome light turns off and then arming the alarm while the door is open I then release the triger button and the dome light comes on but the alarm does not know if the door opened.

Cameronjc

Member - Posts: 29

Joined: February 06, 2004

Posted: August 23, 2006 at 11:58 PM / IP Logged

I was not your installer so I do not know how your installer did your system. You should ask them. In most cases it's pretty standard that the alarm is connected to the pre-existing door switch. Perhaps your installer installed a seperate one, or did a crappy install. Possibilities are endless.

Go to the installer and talk with them about it. If it's a factory alarm, go to the dealer and ask about it. If you bought the car with the alarm, go to the store, buy a new alarm and the shop install it for you.

mercury2006

Member - Posts: 3

Joined: August 20, 2006

Location: Australia

Posted: August 25, 2006 at 1:35 AM / IP Logged

have you been trying to scare fish into giving up using your alarm?

Ive got grey knews for you its niether good nor bad.

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.