the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2005 Grand Cherokee problems


Post ReplyPost New Topic
< Prev Topic Next Topic >
azn_fcuk 
Copper - Posts: 104
Copper spacespace
Joined: November 09, 2005
Location: Canada
Posted: November 14, 2006 at 11:13 PM / IP Logged  

I just installed a compustar 2way starter only into this beautiful truck. Now when i remotley start the vehicle the Traction Control light stays on, and the on board computer reads "problem with electronic brake" when i start with key im fine.

Ive checked all my resistence's and their bang on. Also I wirred my 2nd starter and Accessory just like this http://64.85.6.129/extrainfo/diagrams/26500_GRAND-CHEROKEE_CHRYSLERS%20STARTER%202%20AND%20ACCESSORY%20DIAGRAM.pdf

Now i used universal bypass for transponder and a CAN SL for my anti theft and accessorys.

Im also getting positvie feed back into my Ground in while Running wire, Door locks, and Trunk release.  I diode isolated my Ground in while running wire and my 2nd starter wire. 

IM SO CONFUSED

tha

azn_fcuk 
Copper - Posts: 104
Copper spacespace
Joined: November 09, 2005
Location: Canada
Posted: November 15, 2006 at 11:51 AM / IP Logged  
any takers
Hymer 
Silver - Posts: 695
Silver spacespace
Joined: November 20, 2004
Location: United States
Posted: November 15, 2006 at 1:36 PM / IP Logged  
Where are you pullung your main 12v supply from.... if it's from lt blu and red it could be causing a problem.. ran into that before.. Pull your main power directly from tha battery... personally I would go with the bypass that takes care of all the chrysler bs with resistors and second starter outputs and such... It works great.. saves a lot of headaches
Tire Proz Stillwater Mn
High End Restyling and Comlete Repair
azn_fcuk 
Copper - Posts: 104
Copper spacespace
Joined: November 09, 2005
Location: Canada
Posted: November 15, 2006 at 2:28 PM / IP Logged  

I went right to the battery.

I used the CanSL which takes care of all features like door locks and such, which is why i cant figaure out where the feed back is comming from

damn

kgerry 
Platinum - Posts: 3,455
Platinum spaceThis member consistently provides reliable informationspace
Joined: February 07, 2004
Location: Saskatchewan, Canada
Posted: November 15, 2006 at 3:00 PM / IP Logged  
sounds like you may have missing powering an extra ign or acc wire... which did you power?
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
azn_fcuk 
Copper - Posts: 104
Copper spacespace
Joined: November 09, 2005
Location: Canada
Posted: November 15, 2006 at 4:00 PM / IP Logged  

I powerd ign, acc is relayed with resistor, the same with 2nd starter.

hmmm

kgerry 
Platinum - Posts: 3,455
Platinum spaceThis member consistently provides reliable informationspace
Joined: February 07, 2004
Location: Saskatchewan, Canada
Posted: November 15, 2006 at 4:58 PM / IP Logged  
should be ok then... i always use a PKU-CH2GX  and dont bother with the relays and resistors and i havent had any issues....
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
azn_fcuk 
Copper - Posts: 104
Copper spacespace
Joined: November 09, 2005
Location: Canada
Posted: November 15, 2006 at 5:17 PM / IP Logged  

the 2nd starter and acc are negative on the data wire right?  it does need a relay. 

or are you saying that bypass will accomodate for neg 2nd starter and acc with the probper resistance?

Hymer 
Silver - Posts: 695
Silver spacespace
Joined: November 20, 2004
Location: United States
Posted: November 15, 2006 at 5:20 PM / IP Logged  
no resistors are needed with the bypass... 2nd start or accy
Tire Proz Stillwater Mn
High End Restyling and Comlete Repair
kgerry 
Platinum - Posts: 3,455
Platinum spaceThis member consistently provides reliable informationspace
Joined: February 07, 2004
Location: Saskatchewan, Canada
Posted: November 15, 2006 at 5:25 PM / IP Logged  
PKU-CH2GX  allows for 2nd start and 2nd acc with built in resistors,,,, bypasses 1st and 2nd gen Sentry key...also disarms oem alarm.... sweet little module....
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Page of 2

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Tuesday, May 24, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer