avistart 4100, ’06 vibe, accessory wire?

Home / the12volt's Install Bay / Car Security and Convenience / avistart 4100, ’06 vibe, accessory wire? (

Topic Closed)

Welcome Guest :)

Members

< Prev Page < Prev Topic Next Topic >

peterubers

Silver - Posts: 706

This member has made a donation to the12volt.com. Click here for more info.

Joined: December 29, 2006

Location: United States

Posted: May 18, 2007 at 11:09 PM / IP Logged

radiorookie wrote:

All fuses checked ok.

I ran two direct power cables from the battery to the two red fused lines going into the r/s module. I than setup a relay with the following configuration:

85: connect to Vibe BLACK/ white wire

86: chassis ground

30: 12 volts fused +

87a: BLACK / YELLOW wire on Vibe

It still does the same thing, when you r/s start the car and there is 12V applied to the BLACK / YELLOW wire in the ignition harness the car does not start. Once I unplugged the relay from the BLACK / YELLOW wire the car will remote start fine (except no accessories).

I am at a loss...I think I have tried all options by now...anymore suggestions?

Oops!! My bad, bro. I meant 87 (NOT 87a).

87a is the terminal ALWAYS CONNECTED to terminal 30 on a 5-pin SPDT relay (i always remember it as "87-always connected"). 87 is the terminal 30 is connected to in the event of a voltage across the solenoid (85-86) ...

so ... connect the BLACK / YELLOW wire to the 87 terminal ---SORRY MAN, I hope this solves your problem now.

The search function is your friend.

peterubers

Silver - Posts: 706

Joined: December 29, 2006

Location: United States

Posted: May 18, 2007 at 11:11 PM / IP Logged

BTW .. i checked, re-checked, and re-checked the wiring diagrams again for the P.Vibe/T.Matrix -- and if the relay correction above does not work, I am completely out of ideas --

Are there more than one BLACK / YELLOW wires?

Can you take a digital photo of your wiring and post it? Sometimes having a fresh pair of eyes look at something will make something jump right out as incorrect.

The search function is your friend.

peterubers

Silver - Posts: 706

Joined: December 29, 2006

Location: United States

Posted: May 19, 2007 at 12:05 AM / IP Logged

Final resort:

Try this; basically, swap the ignition wires:

Connect Pink ( NOT pink/white ) wire of the avital directly to BLACK / YELLOW on vibe.

Relay power to BLACK/ white on the vibe as follows:

-> 85: pink wire off avital

-> 86: chassis ground

-> 87: BLACK/ white wire on Vibe

-> 30: fuse 12 volts + (line from battery).

We're confident that the pink wire off the vibe is doing the right thing b/c it has been remote starting. Therefore, we'll connect this FIRST to BLACK / YELLOW and then relay power to BLACK/ white.

if this does NOT work -- @#$@$@

The search function is your friend.

< Prev Page

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

avistart 4100, ’06 vibe, accessory wire?

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.