1990 nissan 300 zx factory alarm problems

Home / the12volt's Install Bay / Car Security and Convenience / 1990 nissan 300 zx factory alarm problems (

Topic Closed)

Welcome Guest :)

Members

Search

Register

Login

< Prev Topic Next Topic >

jazzcustom131

Copper - Posts: 175

Joined: October 10, 2004

Location: United States

Posted: May 17, 2007 at 5:52 PM / IP Logged

I have an aftermarket clifford installed on this car, and there is some mis communication between it and the factory alarm. When I activate the clifford, the other alarm goes off and the starter kill engages. Even after it goes off, the starter kill stays engaged, so my car hasn't moved for 3 days. Anyone know how i can get rid of the factory alarm?? I don't know where the brain for it is,

Greed is for amateurs.

Disorder,chaos,anarchy now THAT is fun!!

Back to Top

peterubers

Silver - Posts: 706

This member has made a donation to the12volt.com. Click here for more info.

Joined: December 29, 2006

Location: United States

Posted: May 17, 2007 at 7:00 PM / IP Logged

FACTORY ALARM DISARM

GRAY/RED (-)

IN DRIVERS KICK PANEL

I dont' think you can get rid of the factory alarm w/o removing the BECU/mutliplex unit. I would consider resetting the clifford and checking some wiring if you can -- the above wire is the disarm for your factory alarm.

I am not sure, but i'm i don't think Nissan's factory alarm includes a factory starter-kill. I think your best bet at this point would be to disconnect the clifford alarm brain and attempt to start your vehicle. If you cannot, look for a SPDT relay connected to the starter wire and reconnect the wires at the 30 and 87a termina

The search function is your friend.

Back to Top

burns25

Member - Posts: 49

Joined: March 09, 2005

Location: United States

Posted: May 18, 2007 at 3:24 PM / IP Logged

The factory alarm brain is under the passenger seat from what I remember. I also seem to remember not being able to find the factory disarm in the driver's kick but it was in the passenger kick. It's been quite a while since I did one of these so it's a bit hazy.

Back to Top

jazzcustom131

Copper - Posts: 175

Joined: October 10, 2004

Location: United States

Posted: May 21, 2007 at 10:44 PM / IP Logged

so if I snip that Gray/Redwire, the alarm "goes away", correct?

Greed is for amateurs.

Disorder,chaos,anarchy now THAT is fun!!

Back to Top

tonyberg

Copper - Posts: 116

Joined: November 08, 2005

Location: North Dakota, United States

Posted: May 22, 2007 at 9:19 AM / IP Logged

no...if you ground it, it goes away

Back to Top

nobles

Member - Posts: 11

Joined: May 07, 2007

Location: United States

Posted: May 23, 2007 at 3:57 PM / IP Logged

there is a hood pin switch, play with it a little, then use the key to unlock the pass door, the car will sart

(based on something similar I did before)

Back to Top

Sorry, you can NOT post a reply.
This topic is closed.

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

1990 nissan 300 zx factory alarm problems

Sorry, you can NOT post a reply.This topic is closed.

Sorry, you can NOT post a reply.
This topic is closed.