the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

2007 infiniti g35x remote starter


Post ReplyPost New Topic
< Prev Topic Next Topic >
infiniti2007 
Copper - Posts: 67
Copper spacespace
Joined: August 21, 2007
Location: Canada
Posted: September 24, 2007 at 10:44 PM / IP Logged  
Hi everyone,
I try to install my two way remote starter and alarm to my 2007 infiniti g35x. I hooked up my remote start with CAN-SL2 (ver 1.9). I got everything working fine except the vehicle start for more than 15 seconds then it shut off and restart it again. But the second attempt, I see the NO KEY in the speedometer panel. But I thought the CAN-SL2 will take care of that. Could someone tell me what is the problems?. Thanks
Velocity Motors 
Moderator - Posts: 12,488
Moderator spaceThis member has made a donation to the12volt.com. Click here for more info.spaceThis member has been recognized as an authority in Electrical Theory. Click here for more info.spaceThis member has been recognized as an authority in Fabrication. Click here for more info.spaceThis member has been recognized as an authority in Mobile Audio and Video. Click here for more info.spaceThis member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.spacespace
Joined: March 08, 2002
Location: Manitoba, Canada
Posted: September 24, 2007 at 11:39 PM / IP Logged  
Your tach signal is not right. I've had this problem in the past with a few vehicles as well where it would run for almost a minute and then shut off. Try another tach wire and relearn the tach.
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Chris Luongo 
Platinum - Posts: 3,746
Platinum spaceThis member consistently provides reliable informationspace
Joined: May 21, 2002
Location: Massachusetts, United States
Posted: September 25, 2007 at 12:11 PM / IP Logged  
I think Jeff's right.
Also, you could temporarily re-program your unit for voltage sensing, as a troubleshooting tool.
If it works on voltage sense, then it's definitely the tach that's wrong......try switching to something else.
infiniti2007 
Copper - Posts: 67
Copper spacespace
Joined: August 21, 2007
Location: Canada
Posted: September 25, 2007 at 7:46 PM / IP Logged  
This is no tach connection on can-sl2. all you connect tach wire of can-sl2 to tach of remote start, and it will find tach itself through data link from bcm of vehicle ( you hooked data link from can-sl2 to data link of vehicle) . I still don' t know why it shut off after started, and sometimes it works perfectly.
hhh
chadwa2003 
Copper - Posts: 353
Copper spacespace
Joined: January 08, 2005
Location: Canada
Posted: September 25, 2007 at 7:53 PM / IP Logged  
Those tach connections aren't always the best i've had issues with some data tach connections before try a direct connection even if you just float a wire to actually test the system or put it on voltage sensing like chris mentioned.
eric-tech 
Member - Posts: 20
Member spacespace
Joined: September 12, 2007
Location: Quebec, Canada
Posted: September 26, 2007 at 8:14 AM / IP Logged  

IDATALINK       ADS-DLSL-CA

Your gonna have the time of your life installing this on 07 Altima and G35.

www.idatalink.ca

Take your time, a solution is just around the corner :-)
infiniti2007 
Copper - Posts: 67
Copper spacespace
Joined: August 21, 2007
Location: Canada
Posted: September 26, 2007 at 7:11 PM / IP Logged  
Thanks guys. I got it to work. I guess the data tach connections does not works, and I tried to connect the tach of the remote to the tach of vehicle and still does not work, finally I switch to the voltage sensing and it works perfectly. Thanks again.
hhh
enice 
Silver - Posts: 857
Silver spacespace
Joined: March 05, 2006
Location: New York, United States
Posted: September 26, 2007 at 9:32 PM / IP Logged  
There may be something you did wrong,  the tach from the vehicle didn't learn.  Which wire did you use???
Chris Luongo 
Platinum - Posts: 3,746
Platinum spaceThis member consistently provides reliable informationspace
Joined: May 21, 2002
Location: Massachusetts, United States
Posted: September 26, 2007 at 10:16 PM / IP Logged  
Ah sorry, I should have paid more attention the first time.
The CAN-SL2i's tach output is incredibly crappy.
It'll work about 80% of the time.
Sometimes it doesn't put out any tach signal, and the remote starter will just keep on grinding the car's starter motor, even after the engine is already running.
Those cars work just fine on voltage sense.
infiniti2007 
Copper - Posts: 67
Copper spacespace
Joined: August 21, 2007
Location: Canada
Posted: October 03, 2007 at 8:39 PM / IP Logged  
Hi, I have installed the alarm/remote start on my 07 infiniti g35x. I got it working perfectly, but Just one problem on the (-) door unlock. Sometimes it works and sometimes it does not. Every time, I disarm the system, sometime it does not unlock the doors (It does disarm the system), and sometime it works (unlock and disarm the system). Could someone tells me what is the problems ?.     Thanks.
hhh
Page of 3

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Wednesday, September 28, 2022 • Copyright © 1999-2022 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer