2003 silverado 2500hd ls, clifford rsx 3.5

Home / the12volt's Install Bay / Car Security and Convenience / 2003 silverado 2500hd ls, clifford rsx 3.5 (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

craigjschr

Member - Posts: 7

Joined: April 19, 2007

Location: Greece

Posted: April 19, 2007 at 10:58 PM / IP Logged

i was wondering if i need a 456g for my truck it says if you hae the base model then no. i already have a 555l for my passlock.

craigjschr

Member - Posts: 7

Joined: April 19, 2007

Location: Greece

Posted: April 19, 2007 at 11:46 PM / IP Logged

what do i need. to install a cliffod Rs3.5. on this truck i already have a 555l for the passlock. also if i could get a wireing diagam.

Mike M2

Platinum - Posts: 2,652

Joined: June 29, 2005

Location: United States

Posted: April 20, 2007 at 6:28 AM / IP Logged

12volts	red (x2)	+	ignition harness
Starter	yellow	+	ignition harness
Second Starter	N/A
Ignition	pink	+	ignition harness
Second Ignition	white	+	ignition harness
Notes: To avoid the check engine light from coming on and possible damage to the automatic transmission, the second ignition in this vehicle MUST be powered when adding a remote start system.
Third Ignition	N/A
Accessory	orange	+	ignition harness
Second Accessory	brown	+	ignition harness
Keysense	lt. green	-	ignition harness
Power Lock	use Directed module 1700G
Notes: If interface module is not available, refer to DirectFax document 1601. On base model trucks, the interface module is not necessary. Instead, the lock wire is lt. blue (-), pin B5, and the unlock wire is white (-), pin B10. They are in the lt. blue plug at the BCM.
Power Unlock	see power lock
Lock Motor	gray	5wi	driver door module in door
Unlock Motor	tan	5wi	driver door module in door
Parking Lights+	brown	+	driver kick panel
Parking Lights-	gray/black	-	BCM, brown plug, pin B2
Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back.
Hazards	white	-	steering column, 5 pin plug
Turn Signal(L)	dk. green	+	steering column, 5 pin plug
Turn Signal(R)	lt. green	+	steering column, 5 pin plug
Reverse Light	lt. green	+	BCM, black plug, pin F
Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back.
Door Trigger	gray/blk (L), BLACK/ wht (R)	-	each door module in each door
Notes: On base model trucks the door trigger wires are in the lt. blue plug at the BCM, pins B4 and A5. On 4dr trucks the LR door trigger is lt. blue/black, pin A3, and the RR is lt. GREEN/ black, pin A2. They are in the purple plug at the BCM. Use all wires and diode isolate. The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back.
Dome Supervision	gray/black	+	BCM, black plug, pin E
Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back.
Trunk/Hatch Pin	N/A
Hood Pin	N/A
Trunk/Hatch Release	N/A
Power Sliding Door	N/A
Factory Alarm Arm	arms with lock
Factory Alarm Disarm	lt. green	-	driver door module in door
Disarm No Unlock	see factory alarm disarm
Tachometer	white	ac	instrument cluster, pin A5 or PCM
Notes: The PCM (Powertrain Control Module) is in the left front of the engine compartment to the left of the fan shroud. The tach wire is in the green plug, pin 10. For tach can also go to any of the ignition coils or injectors and use the wire that is NOT pink, black, or brown.
Wait to start	dk. blue	-	instrument cluster, pin A2 or PCM
Notes: The PCM (Powertrain Control Module) is in the left front of the engine compartment to the left of the fan shroud. The wait to start wire is in the green plug, pin 36. On the remote start, make sure to program the Accessory State During Wait To Start to ON.
Brake Wire	white	+	brake pedal switch
Parking Brake	lt. blue	-	BCM, lt. blue plug, pin A7
Notes: The BCM (Body Control Module) is under the driver side dash. It has 6 plugs in it, the purple plug is on the back.
Horn Trigger	BLACK / YELLOW to black	-	steering column
Memory Seat 1	red	+	driver door module in door
Memory Seat 2	pink	+	driver door module in door
Memory Seat 3	N/A	+

Interface Module:	Category: Immobilizer Bypass	Required: Yes	Type: Passlock II
Part #: 1100F
Alternate Part1 #: 1100X
Alternate Part2 #: 556LW
Alternate Part3 #: 555LW

Mike M2

Tech Manager

CS Dealer Services

KarTuneMan

Platinum - Posts: 7,056

This member has made a donation to the12volt.com. Click here for more info.

This member consistently provides reliable information

Joined: December 14, 2004

Location: Isle Of Man

Posted: April 20, 2007 at 8:16 AM / IP Logged

Get the door lock module as well.

KarTuneMan

Platinum - Posts: 7,056

Joined: December 14, 2004

Location: Isle Of Man

Posted: April 20, 2007 at 8:18 AM / IP Logged

yes...or a simular module, from a different manufacturer.

Velocity Motors

Moderator - Posts: 12,488

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: April 20, 2007 at 8:37 AM / IP Logged

2003 + Silverado's require a module for the door locks to operate. You can check to see if the BCM has the door lock wires in the BROWN plug at the BCM or the LIGHT BLUE plug at the BCM.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

craigjschr

Member - Posts: 7

Joined: April 19, 2007

Location: Greece

Posted: April 20, 2007 at 8:34 PM / IP Logged

whare is the nutral switch

thanks

Mike M2

Platinum - Posts: 2,652

Joined: June 29, 2005

Location: United States

Posted: April 20, 2007 at 9:35 PM / IP Logged

Is the truck a clutch or automatic?

Mike M2

Tech Manager

CS Dealer Services

craigjschr

Member - Posts: 7

Joined: April 19, 2007

Location: Greece

Posted: April 20, 2007 at 10:41 PM / IP Logged

automatic

enice

Silver - Posts: 857

Joined: March 05, 2006

Location: New York, United States

Posted: April 20, 2007 at 11:11 PM / IP Logged

neutral wire is BLACK/ white on the alarm. it needs to see a ground input when remote started, what you can do is just ground it. On the other hand you can connect that wire to a switch that comes with the alarm. one side to that BLACK/ white wire and the other to ground.

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.