the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

amp questions


Post ReplyPost New Topic
< Prev Topic Next Topic >
Jmeese 
Copper - Posts: 114
Copper spacespace
Joined: June 03, 2005
Location: United States
Posted: July 14, 2005 at 4:46 PM / IP Logged  

Ok couple of questions:

Does the amp have to be anchored or can you leave it so it can be moved.  It will be under the seat and not sliding around but I don't have a level surface to mount it to.  I may be able to anchor 1 corner of it..

Also can the speaker wire run down the same path as the rca's.  I have the power seperated from the rca's.

The remote turn on for the amp, does this get connected to the continuous power wire of the Hu?

Bigsingh 
Copper - Posts: 204
Copper spacespace
Joined: March 26, 2005
Posted: July 14, 2005 at 5:05 PM / IP Logged  
ull want to mount ur amp, to keep it from getting knocked about. atleast two screws, one in each opposite side. now you can run your speaker wire with your rca no probs. keep the power wire away. now on the back of your headunit will be a blue wire with most likely a connector, the wire is usually blue with a white stripe. now just connect the remote cable to this and your sorted.
6* Rockford T2's
6* POWER AMPs
BLACK CORRADO
BAANNGGIINN
JAydawg21 
Copper - Posts: 51
Copper spacespace
Joined: July 01, 2005
Location: United States
Posted: July 14, 2005 at 7:52 PM / IP Logged  

Well, if you wanna do a shody job, you dont necesaraly have to mount it.  If you drive like a nut and it slides all over and strts shorting wires and stuff, you'll have a problem.  Other wise you'll just get made fun of.  As far as mounting under the seat goes, I def. wouldnt recomend that.  Depending on how hard you work your amp its gonna over heat and start cutting out on you.  If you ever touched an amp workin over time for a while you know that you can literally fry an egg on one.  Amps are designed to be mounted out in the open and some even suggest mounting it upright depending on heat sink alignment.  If you really wanna go under the seat and do a good custom job (which it doesnt sound like you do), you'd have to put in fans and vents. 

'97 Jeep Cherokee sport
subs: JL 12w3v2 : RF 500a2 :
RF 1F capacitor
doors: 6" Diamond D361i -> RF 200a4
boulderguy 
Silver - Posts: 510
Silver spacespace
Joined: April 17, 2005
Location: United States
Posted: July 15, 2005 at 2:01 AM / IP Logged  

Don’t worry about fans under a seat, unless it’s really tight it should have plenty of air flow.  A couple tricks – pull out the seat & throw a piece of MDF under the carpet & amp, then screw the amp to that.  Or, and I like this, cut an “X” into the carpet under the amp, fold it under & mount the amp beneath the carpet with the heat sinks sticking up & thru – airflow & concealed wires, no screws, totally secure.


Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, October 31, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer