04 nissan maxima, remote start

Home / the12volt's Install Bay / Car Security and Convenience / 04 nissan maxima, remote start (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

TooDark

Copper - Posts: 163

Joined: September 10, 2002

Location: United States

Posted: January 17, 2009 at 9:48 AM / IP Logged

I have installed a CS2900 w/CAN SL2 for bypass into a Maxima with some problems. When it is remoted started the the heater works but no windows, turn signals, radio and no power to the radio/heater screen (which is fine) but, after the car takes over the windows and turn signals still do not work. I have to shut the car off and start it w/the key and everything is OK then. 12 volt=green, ing=sm blk/red, acc=red and I have also connected the wht/blu, start=blk/red, start2=blk/red Anyone ideas? Have beenon phone with tech support ad they can not even figure it out.

advanced

Copper - Posts: 207

Joined: January 13, 2003

Location: Massachusetts, United States

Posted: January 17, 2009 at 10:01 AM / IP Logged

BTW, starter 2 should be BLACK / YELLOW.

Sounds silly, but are you sure you have the brake wire hooked up right? Does the engine stop when you get in & hit the brake, after remotely starting? If not, you are still under the remote start power & maybe one of the wire connections you made to the igmition is loose.

Also, use a voltmeter & check for voltage output on all remote start ignition wires. I'm sure one of the ignition wires is not getting powered up somehow.

Good Enough Isn't!

Chris Luongo

Platinum - Posts: 3,746

This member consistently provides reliable information

Joined: May 21, 2002

Location: Massachusetts, United States

Posted: January 17, 2009 at 10:05 AM / IP Logged

And you didn't say exactly what you connected to the WHITE/ blue.

The first step would be to test all of the car's ignition, accessory, and starter wires for proper function during remote start. That is, not visually, but testing with your test light or multimeter.

TooDark

Copper - Posts: 163

Joined: September 10, 2002

Location: United States

Posted: January 17, 2009 at 10:16 AM / IP Logged

Starter2 blk / YELLOW (that is what I ment, typo) The brake is hooked up properly, when I get in and hit the brake the car shuts down. Sorry, the WHITE/ blue I have hooked up as another acc, tech support had me hook up another acc wire, the WHITE/ blue tests as an acc on the car. I have tested all the wires from the RS and they all seem to working like they are suppose to. All wires on the car have been tested along with RS with a multimeter. This one is kicking my ass and I'm lost.

advanced

Copper - Posts: 207

Joined: January 13, 2003

Location: Massachusetts, United States

Posted: January 17, 2009 at 10:33 AM / IP Logged

Try this experiment:

With the car is running under the power of remote start only, connect your ignition wire BLACK/ red to Red first & then to WHITE/ blue. Do one at a time & see if radio,etc. comes on with either one.

Let me know what happens.

Good Enough Isn't!

TooDark

Copper - Posts: 163

Joined: September 10, 2002

Location: United States

Posted: January 17, 2009 at 11:12 AM / IP Logged

OK, Radio, screen and interior lights come on when ING is connected to WHITE/ blue, but no turn signals doring RS nor when car takes back over from RS. If I shut car off and start w/key turn signals work. Any more ideas????

advanced

Copper - Posts: 207

Joined: January 13, 2003

Location: Massachusetts, United States

Posted: January 17, 2009 at 11:20 AM / IP Logged

OK, sounds like the WHITE/ blue is not getting power during remote start.

Now temporarily try connecting the ignition wire BLACK/ Red to Red & WHITE/ Blue together (All 3 together). Tell me if turn signals work.

Good Enough Isn't!

TooDark

Copper - Posts: 163

Joined: September 10, 2002

Location: United States

Posted: January 17, 2009 at 11:34 AM / IP Logged

no turn signals, during RS nor when car takes back over. ????????????????

Mike M2

Platinum - Posts: 2,652

Joined: June 29, 2005

Location: United States

Posted: January 17, 2009 at 11:40 AM / IP Logged

You have a problem with power to one of the accessory wires. Check them again with a DVM while Rs is on...

Mike M2

Tech Manager

CS Dealer Services

TooDark

Copper - Posts: 163

Joined: September 10, 2002

Location: United States

Posted: January 17, 2009 at 12:14 PM / IP Logged

went through a whole RS cycle and measured all wires during the cycle. All wires are getting 12Volts when they are suppose to.

Measured wires at car and at the RSer.

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.