98 corolla with viper 5701

i am getting confused about BLACK/ white wire(ignition 1 some say it is) and BLACK / YELLOW wire(Ignition 1 some say it is too) and my car BLACK/ white wire looks more like gray/white. Is their a way of testing them. I only know yellow/black powers dashboard like you would turn the key into on position.

Test the vehicles ignition wires with a Digital Multi Meter.  Below is a guide for

wire identification.

Battery  +12V Constant:

Verification: This wire will register ( + ) voltage in all positions of the ignitionswitch.

Ignition:

Verification: This wire registers voltage when the key is turned to the ON (orRUN) position. The voltage does not drop out when the key is turned to theSTART (or CRANK) position.

Starter:

Verification: This wire registers voltage only when the key is turned to theSTART position.

Accessory Wire:

Verification: This wire registers voltage when the key is turned to ACC(Accessory) and the ON (or RUN) position. The voltage drops out when thekey is turned to the START (or CRANK) position.

1998 Toyota   Corolla  ( Info from DEI.)

Signal                Color                       Location                                                           Viper H312volts              white (50A)  +       ignition switch, white 8 pin plug, pin 2            H3/2, H3/6, H3/9Starter              red  +                     ignition switch, white 8 pin plug, pin 8 - cut    H3/4 Car Side, H3/5 Key SideIgnition             BLACK/ white  +        ignition switch, white 8 pin plug, pin 6            H3/1Ignition2           BLACK / YELLOW  +      ignition switch, white 8 pin plug, pin 4            H3/7Accessory       blue/red  +             ignition switch, white 8 pin plug, pin 3            H3/3 This DEI info is only a guide and should be verified.  Wire colors can fade with age.

Soldering is fun!

Thank you for your reply it will save time and also when i test wire ignition wires can voltage drop 10v in start position and increase to 13v or 14v or has to stay died on 12v One more thing Remote start input, 5-pin connector and Remote start auxiliary output, 5-pin wire from does two connters are requered to just test if the remote will start the car. I just have Tach (VIOLET/WHITE) wire hacked up.

A standard car battery will be about 12.3V.  While the starter is cranking it can drop to around 10V.  While the engine

is running and the alternator is supplying the vehicles needs, it will read around 14.3 V.

Remote start input, 5-pin connector                                                            Needed?              Use         

1 BLACK/ WHITE (-)                NEUTRAL SAFETY SWITCH INPUT             Mandatory       If Auto Trans, connect to chassis ground.  2 VIOLET/WHITE                   TACHOMETER INPUT WIRE                        Optional           Most reliable remote start operation.3 BROWN (+)                         BRAKE SHUTDOWN WIRE                           Mandatory       Connect to (+) Brake Pedal wire4 GRAY N/O or N/C (-)           HOOD PIN SWITCH INPUT, ZONE 6             Mandatory       Connect to Hood Pin Switch5 BLUE/WHITE (-) 200 mA     2ND STATUS/REAR DEFOGGER                Optional           Various uses

Remote start auxiliary output, 5-pin

1 PINK/WHITE (-) 200mA     FLEX RELAY CONTROL OUTPUT                 Optional   Not needed on '98 Corolla2 ORANGE (-)     200mA     ACCESSORY OUTPUT                                   Optional   Not needed on '98 Corolla     3 VIOLET (-)     200mA       STARTER OUTPUT                                         Optional   Not needed on '98 Corolla4 PINK (-)       200mA          IGNITION 1 OUTPUT                                       Optional   Not needed on '98 Corolla5 BLUE (-)       200mA         STATUS OUTPUT                                           Optional   Not needed on '98 Corolla

Soldering is fun!

Here is a link to the Viper 5701 Install guide :  https://www.the12volt.com/installbay/file.asp?ID=710 

There are many things that need to be done for a successful install.  You will need it for setting the Program Options and the Tach Learn process, etc.  

Soldering is fun!

thank you for the advice but remote start still does not work at list starts when i use the key. when i use the remote to start it takes long beep and show red by the function button.

What error do you get from the parking lights?commit your way to jehovah and he will act in your behalf. psalms 37:5

Hard count like 7,8 or 9 it blinked so fast

The 5701 comes with the Manual Transmission mode as the default setting in menu 3. Follow the guide to change it to automatic and then program your tach, run time etc. and you'll be fine

Tell me you're joking about the hard count.commit your way to jehovah and he will act in your behalf. psalms 37:5