05 chevy equinox will not crank

Hi there, just wondering if I could get any hints or tips. I have a 05 chevy equinox that I am installing a viper 4104 in to and I have 2 questions. First door lock wires are + polarity and the viper kit says its output is - polarity, how would i get this working? now the big one, I have everything else hooked up and ready to go but the remote start activates and i get power on ignition and 2 accessories and then lose the power on 2 accessories and then it is supposed to crank. But does not crank at all. This install says it does not require a starter output wire to crank. I am kind of lost on what to do to get this vehicle to crank with the remote start. Please any help would be greatly appreciated. Thanks

What bypass are you using?

You should have 2 ignitions and 1 Accessory

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

xpresskit XK09 DLPKGM

and the wiring color code sheet says it has 2 accessories and 1 ignition

What wiring code sheet are you refering to? The type 6 install for the xk09 shows 2 ignitions and 1 acc.  Have you tested and verified the wires on the ignition switch with a DMM?

You will also have 2 wires from the 20 Pin xk09 connector to the starter output and the ignition 1 output of the Viper unit, on the way to the wiring harness of the car.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

This is the wiring info I am referring to off of this site. maybe this info is wrong about the 2 accessories and 1 ignition? CHEVROLET / EQUINOX / 2005 / Remote Start 12volts RED / white (x2)   +   ignition harness Starter yellow (not for remote start)   -   PCM, blue plug, pin 23 Notes: Starter wire is not required for remote start. When the vehicle sees that the ignition wire has voltage and the two accessory wires lose voltage, it automatically cranks the starter. The PCM is located in front of the driver strut tower, above the battery cover. Second Starter N/A        Ignition pink   +   ignition harness Second Ignition N/A        Third Ignition N/A        Accessory orange   +   ignition harness Second Accessory brown   +   ignition harness Keysense lt. green (required)   -   BCM, 24 pin gray plug, pin A8 Notes: The BCM is located in the center console, below the radio. Power Lock lt. blue   +   BCM, pink plug, pin B4 Notes: The BCM is located in the center console, below the radio. Power Unlock dk. blue   +   BCM, 24 pin gray plug, pin A3 Notes: The BCM is located in the center console, below the radio. Lock Motor gray   5wi driver kick, door harness Unlock Motor tan   5wi driver kick, door harness Parking Lights+ brown   +   BCM, 24 pin gray plug, pin B7 Notes: The BCM is located in the center console, below the radio. Parking Lights- lt. blue   -   BCM, 24 pin gray plug, pin B3 Notes: The BCM is located in the center console, below the radio. Hazards same as turn signal wires        Turn Signal(L) lt. blue   +   steering column Turn Signal(R) dk. blue   +   steering column Reverse Light lt. green   +   kick panel, harness to rear Door Trigger gray/black and tan/white   -   BCM Notes: The driver door trigger is gray/black in the pink plug, pin B8. The passenger doors trigger is tan/white in the 24 pin gray plug, pin B5. Use both wires and diode isolate each. The BCM is located in the center console, below the radio. Dome Supervision white   -   BCM, pink plug, pin A1 Notes: The BCM is located in the center console, below the radio. Trunk/Hatch Pin ORANGE / black   -   BCM, pink plug, pin B12 Notes: The BCM is located in the center console, below the radio. Hood Pin N/A        Trunk/Hatch Release N/A        Power Sliding Door N/A        Factory Alarm Arm factory remote only        Factory Alarm Disarm factory remote only        Disarm No Unlock with ignition and Passlock        Tachometer purple   ac   PCM, black plug, pin 61 Notes: The PCM is located in front of the driver strut tower, above the battery cover. Wait to start N/A        Brake Wire lt. blue   +   brake pedal switch Parking Brake lt. blue   -   BCM, pink plug, pin B5 Notes: The BCM is located in the center console, below the radio. Horn Trigger tan   -   BCM, pink plug, pin A3 Notes: The BCM is located in the center console, below the radio. Memory Seat 1 N/A        Memory Seat 2 N/A        Memory Seat 3 N/A        Interface Module: Category: Immobilizer Bypass Required: Yes Type: Passlock II Part #: 556LW Alternate Part1 #: 555LW Alternate Part2 #: 555T Alternate Part3 #: DesignTech 20402 Alternate Part4 #: DesignTech 29402 Notes: The Passlock II wire colors are yellow, ORANGE / black, and ORANGE / white (not used).

My apologies, there are 2 Acc and 1 ignition on that car. And no starter wire. I did one back in October using a DB-ALL  W2W.

Link to that posting:  https://www.the12volt.com/installbay/forum_posts.asp~TID~132274~KW~smokeman1~PN~1~TPN~1

Even tho the wiring show a connection to the car for starter on the DB-ALL, I did not connect it.  Follow the notes Kreg provided me,  Test the wires you are using.

Most likely the starter output from the Viper goes to the starter input of the XK09.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

ok thanks. Im going to try to hook up the bypass w2w. i was using the d2d connection and apparently there have been some issues with using that method

what does the keysense wire on the vehicle get hooked up to?

I don't see a keysense on the wiring diagram.When all else fails, Read the Instructions

Support the12volt.com Make a Donation