viper 4204v + db all in civic 2012 manual

I want to install Viper 4204V remote start with db-all in my 2012 civic. In the past I install a Viper 350 Car alarm in my 77 t/a without any problem But my civic look like more complicated and viper manual (4204)is not detail like the 350 I get a diagram with the Xpresskit for my civic connection, civic 2012 db-all The wire in the rec rectangle in image goes with wich one of the viper wire? viper 4204 harness1 viper 4204 harness2 Thanks and my car is manual so I think that I should connect h2/2 hire to e-brake switch !?

Use the wire diagram template stickied to the top of the Security & Convenience page to list out all of the connections. It will help us to help you. But I can tell you right now that you probably won't get any help on here for that installation. That is not the correct starter for a manual transmission and is a MAJOR safety hazard. There is nothing that will prevent the car from being able to start in gear and could potentially kill someone. Get a starter that is manual transmission ready and we will be more than willing to help.Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205

I am not a Viper dealer, but from the info I can find online, it appears that the Viper 4204V is manual transmission safe ( has a reservation mode, etc ).

http://www.viper.com/ShopViperProducts/ItemDetail.aspx?ItemCode=4204V

Fill out the templates and that should get things started.  Remember that installing a remote start on a manual transmission vehicle is more complicated and has to be done correctly to ensure safe operation.

Soldering is fun!

This remote start have a reservation mode on it, you have to put car in neutral, push the break pedal, pull e-break, remove key get out og the car, press door look button and the car will stop, I try to start the car with the clutch switch jumped(safely in my yard), I put the car in gear and I start it, the car was doing the same thing like im stalling it He don`t start and move like 3 inches...

I have matching some of the connection on paper if some one can double check please (+)Starter:-----------------h3/4 (+)Accessory 1:----------h3/2 (+)Accessory 2:----------h3/5 (+)12v Input:---------------h1/1 (+)Ingnition Output:------h3/1 (-)Ground:-----------------h1/2 (-)parking light:--------- ? I think I have to invert the polarity in the module tu put it negative and h2/2 on e-break wire Thanks to helps me

I apologize. I did a search on here for 4204 and it brought up the 4204V. Unfortunately your method doesn't test it properly. When the remote start cranks the engine, it will continue cranking it until it reads the tach signal (engine actually starts) so if installed incorrectly and activated, it will drive away until it hits a solid object. Do a search in the Downloads/Manuals section for "Wire template". It will give you an Excel document that gives the exact layout to help us help you. Fill that out with what you know (from the Viper manual) and we can help fill in the blanks. A lot of us work full time on here and don't always have the ability to spend an hour making up a template from scratch. If you can get it started, we can fill in the blanks.Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205

I just need the connection in y last post, Im gonna try with d2d methode (I know that is not the best way) so I just need the connection in my first post first link. I know where the connection goes in the car, but I don't know wich viper wire do what Exemple: Accessory 1 (from viper)go to wire on ignition switch white connector pin 4 orange wire Which is Accessory 1 wire on viper harness? I.m completing the excel thing and i gonna post it in few minutes thanks a lot

Here the connection Template with all the connection and information that I have ! Connection Template

Click on the link and click on download on the top left, now you can download the Excel Document on your pc !! Thanks

This should be everything. I didn't bother uploading the actual document, just copied / pasted so the format isn't perfect but it should get you going. Also, you are better off going W2W. 5 extra minutes of prep time could end up saving you hours of headache in the future. Vehicle Information: Honda Civic 2012 Ex Manual trans.    Alarm / Remote Start Unit: Viper 4204V    Bypass Module: Db-all w Firmware honda56    Alarm / Remote Start / Bypass Unit   Vehicle Connection     Color     Description     Color     Polarity     Location: h1/1     Red     (+) 12vdc Constant Input     White     (+)     Ignition Switch/White Connector/Pin 1 h1/2     Black     (-) Chassis Groun     n/a     (-)     Body Ground h1/3     Brown     (-)200mA Horn Honk Output     orange or pink     (-)     horn switch or dash fuse box, 38 pin plug C; pin 37 h1/4     WHITE/ rown     Light flash isolation wire - pin 87a light flash relay     No connection h1/5     White     Pin 30 of light flash relay     gray     (-)     headlight switch (*Change Viper jumper to (-) light output h1/6     Orange     500 mA Ground when Armed output     No connection h2/1     Pink/white     (-) 200 mA flex relay control Output     No connection h2/2     BLACK/ White     (-) Neutral Safety input     GREEN/ red     -      e-break switch h2/3     Blue/White     (-) 200 mA 2nd status/rear defogger output     No connection h2/4     GREEN/ Black     (-) 200 mA Factory alarm disarm output     To DB-ALL h2/5     RED / White     (-) 200 mA Trunk release Out put     To DB-ALL h2/6     Green     (-) Door Input     To DB-ALL h2/7     BLACK / YELLOW     (-) 200 mA Dome light output     No connection h2/8     n/a     Empty    h2/9     Dark Blue     (-) 200 ma Status Output     To DB-ALL h2/10     Pink     (-) 200 mA Ignition 1 Outout     No connection h2/11     WHITE/ Black     (-) 200 mA Aux 3 Output     No connection h2/12     Violet      (+) Door Input     No connection h2/13     WHITE/ Violet     (-) 200 mA Aux 1 Output     No connection h2/14     Violet/Black     (-) 200 mA Aux 2 Output     No connection h2/15     ORANGE / Black     (-) 200 mA Aux 4 Output     No connection h2/16     Brown     (+) Brake Shutdown Input     light green     +     brake switch or dash fuse box, green 44 pin plug B; pin 8 h2/17     Grey     (-) Hood pin Input (nc or no)     light blue     (-)     dash fuse box, 38 pin plug C; pin 27 (*If factory equipped) h2/18     Violet / YELLOW     (-) 200 mA Starter Input     No connection h2/19     Blue     Factory Horn Input (use jumper tu set polarity)     No connection h2/20     Gray/Black     (-) Diesel wait to start Input     No connection h2/21     WHITE/ Blue     Activation Input     No connection h2/22     Orange     (-) 200 mA Accessory Output     No connection h2/23     Violet/White     Tachometer Input     To DB-ALL h2 /24     GREEN / WHITE     (-) 200 mA Factory Alarm Arm Output     To DB-ALL h3/1     Pink     (+) Ignition 1 Input/Output     blue     +     Ignition switch h3/2     RED / White     (+)12v Fused(30A) Ignition 2/Flex Relay Input     White (50A)     +     Ignition switch h3/3     Orange     (+) Accessory Output     orange     +     Ignition switch h3/4     Violet     (+) Starter Output     yellow     +     Ignition switch h3/5     Red     (+)12V Fused(30A) Ignition1 Input     White (50A)     +     Ignition switch h3/6     Pink/White     Ignition 2/Flex Relay Output     red     +     Ignition switch (change Viper programming to 2nd accessory) h3/7     Pink/Black     Flex Relay Input 87a (if required) Of Fles Relay     No connection h3/8     RED / Black     (+)12V Fused (30a) Accessory/Starter Input     White (50A)     +     Ignition switch Door lock 3 pins 1     Blue     (-) 500 mA unlock Output     No connection 2     Empty     n/a    3     Green     (-) 500 ma Door Lock Output     No connection Kenny

Owner / Technician

KKD Garage LLC

Albany, NY 12205