auto security model imp-4040

Home / the12volt's Install Bay / Car Security and Convenience / auto security model imp-4040 (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

slyguy61520

Member - Posts: 9

Joined: December 30, 2004

Location: United States

Posted: January 11, 2005 at 11:08 AM / IP Logged

i have the door lock unlock working but it says with 3 flashes that i have a zone problem . it says to hook green to door - trigger to door pin neg which i believe is the purple wire in drivers door kick panel and is landed there. the shock sensor is installed.all the doors when opened one at a time sound alarm.what am i missing? also remote start will not work .i have a n c 30 relay wired inline of the starter yellow wire with the 12v pos off of battery to one side and the orage - armed output to the other side. i put the violet starter wire from the remote start to the ign side of the relay.when i push the remote start button the accesory wire comes on but not the start. i have the blue hood pin wire to the white brake wire with the yellow also from the remote. thoughts? thx in advance. this is on a 2000 gmc savanna

slyguy61520

Member - Posts: 9

Joined: December 30, 2004

Location: United States

Posted: January 11, 2005 at 4:37 PM / IP Logged

well never mind the alarm part of the question i've got that part fixed.

slyguy61520

Member - Posts: 9

Joined: December 30, 2004

Location: United States

Posted: January 11, 2005 at 5:52 PM / IP Logged

now all i need to know is the starter kill relay powered from any 12 + source or does it have to be from the ign power and does it matter which side i connect the violet wire from the remote start brainbox to the relay?

gcorrea

Silver - Posts: 436

Joined: May 22, 2004

Location: United States

Posted: January 12, 2005 at 12:29 AM / IP Logged

if you use a pre wired relay it will get 12 volts from the starter wire itself, key side of course. you can do that to. if your relay is not pre wired, or you can tap into a 12 volt constant at the ignition switch.

gcorrea

Silver - Posts: 436

Joined: May 22, 2004

Location: United States

Posted: January 12, 2005 at 12:59 AM / IP Logged

your gmc has a second ignition wire that has to be powered up its a pink/ white wire or white. first ignition is pink. and your stater wire is yellow. post the wires on you rs unit, color codes.

gcorrea

slyguy61520

Member - Posts: 9

Joined: December 30, 2004

Location: United States

Posted: January 12, 2005 at 5:52 AM / IP Logged

ok thx. here goes . i have the starter wire yellow going through the relay's n c contacts. i have the 12+constant power from ign wire ahead of the key.. i need to know which side of the nc contacts the violet starter wire from rs goes. i dont think it matters but not sure. the wire colors are as follows violet=starter, orange=accessory,yellow=ignition1,brown=ign2 is needed thisone i dont have wired do i need to wire it? red==12+input,red=12+input blue =hood pin or extra light switch+when brake is applied yellow=connect to brake light switch +when brake is applied

gcorrea

Silver - Posts: 436

Joined: May 22, 2004

Location: United States

Posted: January 12, 2005 at 6:53 PM / IP Logged

violet goes to your vans yellow starter wire

orange goes to your vans orange wire acc.

yellow goes to your vans pink wire

brown goes to your pink/white wire or white on your van, yes you need this wirehooked up.

red of course is 12 volt constant

blue wire is a negative input because it is grounded when your hood pin engages

yellow receives a 12 volt input when your brake pedal is depressed.

gcorrea

slyguy61520

Member - Posts: 9

Joined: December 30, 2004

Location: United States

Posted: January 12, 2005 at 7:26 PM / IP Logged

so the violet doesnt matter which side of the relay? also the hood pin can be connected to the same wire as the yellow going to the brake peadl? i will try all this on thurs . thx

gcorrea

Silver - Posts: 436

Joined: May 22, 2004

Location: United States

Posted: January 12, 2005 at 8:23 PM / IP Logged

no. your pin switch is negative input while your brake wire is a positive input. tour pin and brake inputs have to be independant from each other. violet wire of the rs goes after the kill relay or also called the starter side.

gcorrea

slyguy61520

Member - Posts: 9

Joined: December 30, 2004

Location: United States

Posted: January 12, 2005 at 10:01 PM / IP Logged

ok thx glad i read this before i finished wiring it. so where can i land my neg input inside the van? thx

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.