2000 mazda protege keyless entry

Home / the12volt's Install Bay / Car Security and Convenience / 2000 mazda protege keyless entry (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

Methree

Member - Posts: 15

Joined: August 09, 2005

Location: United States

Posted: August 09, 2005 at 9:42 PM / IP Logged

ok, got the kick panel out and i found the GREEN/ red wire. but how do i wire into it to make my keyless entry work? i understand that it grounds out the 12v source to unlock it but i wasnt sure how to wire this. do i end up w/ 2 wires attached to it or do i end up w/ one wire attached to the GREEN/ red wire? i also have a BROWN / black wire that is also connected to the lock. lmk what you guys think. thanks alot for the help. btw i wasnt sure what forum to post under so i also posted under wiring diagrams. sry bout that.

-robert

Methree

Member - Posts: 15

Joined: August 09, 2005

Location: United States

Posted: August 09, 2005 at 9:59 PM / IP Logged

btw whenever i do it like the manual says it always unlocks the door. there is no locking at all. and the unlock button does not activate anything with the car. the lock button unlocks the locks when i hook it up like the diagram says. i have the 2 wire system, where only one wire controls both or something like that

dare_ds69

Silver - Posts: 419

Joined: January 25, 2005

Location: New Jersey, United States

Posted: August 10, 2005 at 6:15 AM / IP Logged

Power Lock	lt GREEN/ red	-	module high in driver kick
Notes: This is a one wire system, must use relays. Lock requires negative trigger through a 1.5K resistor, Unlock requires a negative trigger to the same wire.
Power Unlock	same wire

you need two relays and a resistence of 1.5K or use one relay like that

86 12v fused

85 (-) lock fron alarm

87 resistence 1.5K negative

87a (-) unlock from alarm

30 goes to light GREEN/ red on the car.

how own your mind, control your life.

MECP certified. always use a DMM

Methree

Member - Posts: 15

Joined: August 09, 2005

Location: United States

Posted: August 10, 2005 at 8:28 AM / IP Logged

where do i get the resistor from?

Methree

Member - Posts: 15

Joined: August 09, 2005

Location: United States

Posted: August 10, 2005 at 8:28 AM / IP Logged

also what number/ part number is it? could i go to radio shack to get it? thanks for the help also!!

mo12v

Platinum - Nominee - Posts: 2,748

This member consistently provides reliable information

Joined: September 30, 2003

Location: Afghanistan

Posted: August 10, 2005 at 8:47 AM / IP Logged

Radio Shack 1.5 Resistor 1/4 Watt....about $2.00 for 4

Don't Learn from Others Mistakes

You Might Be the One That Knows.

Methree

Member - Posts: 15

Joined: August 09, 2005

Location: United States

Posted: August 10, 2005 at 10:11 AM / IP Logged

where do i get the relays from?i am on my way to radio shack in a bit. thanks for the info.

Methree

Member - Posts: 15

Joined: August 09, 2005

Location: United States

Posted: August 10, 2005 at 2:26 PM / IP Logged

ok, got a relay from best buy. hooked it all up and the unlock button works but the lock button does not... how do i hook the resistor into the line? should i check the 2nd unlock wire for amperage or something? the unlock wire may not be doing its job or something but i dont have the resistor pluged in anywhere. where should i plug it into? lmk thanks

Methree

Member - Posts: 15

Joined: August 09, 2005

Location: United States

Posted: August 10, 2005 at 3:10 PM / IP Logged

ok, how do i hook the 1.5k resistor to it? and when you say negative lock and unlock, i only have 2 wires that it says to connect. a green and blue one. the lock button does not make the relay click, but the unlock does.lmk what you guys think is up.l thanks again

Methree

Member - Posts: 15

Joined: August 09, 2005

Location: United States

Posted: August 10, 2005 at 9:34 PM / IP Logged

ok. it does not lock. do i need to use 2 relays? if so i was reading on how to do it but it says i need to connect all the outputs to the same wire. will i have 2 wires going to the GREEN/ red wire? or will i have one to the red green and one to the BROWN / black? do i need 2 relays? lmk thanks.

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.