4113 and dlpk on 08 impala

Home / the12volt's Install Bay / Car Security and Convenience / 4113 and dlpk on 08 impala

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

chiefdone1

Member - Posts: 25

Joined: December 19, 2014

Location: Indiana, United States

Posted: December 21, 2014 at 12:21 PM / IP Logged

Can someone suggest where the antenna for the 4113 should be placed? The end piece has a sticky pad on it.

Chiefdone

kreg357

Platinum - Posts: 7,783

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: January 30, 2009

Location: Pennsylvania, United States

Posted: December 21, 2014 at 12:28 PM / IP Logged

Center of windshield by rear view mirror works best.

Soldering is fun!

chiefdone1

Member - Posts: 25

Joined: December 19, 2014

Location: Indiana, United States

Posted: December 21, 2014 at 2:20 PM / IP Logged

Thanks again.

Chiefdone

chiefdone1

Member - Posts: 25

Joined: December 19, 2014

Location: Indiana, United States

Posted: December 22, 2014 at 10:13 AM / IP Logged

I am installing and expected to find ppl wire at ignition switch to connect ppl from 4113. It is not there. Is this connection needed? Or does comm thru CAN somehow make this unnecessary?

Thanks

Chiefdone

kreg357

Platinum - Posts: 7,783

Joined: January 30, 2009

Location: Pennsylvania, United States

Posted: December 22, 2014 at 10:29 AM / IP Logged

You should not expect to find a Purple Starter wire in the ignition switch harness. The car does not have a traditional Starter wire.

The Purple Starter wire mentioned in the wire guides is under the hood, in the engine compartment, and used for "starter kill" purposes

only. The 4113's Purple (+) Starter Output wire is not used on your vehicle.

Soldering is fun!

chiefdone1

Member - Posts: 25

Joined: December 19, 2014

Location: Indiana, United States

Posted: December 22, 2014 at 10:42 AM / IP Logged

Thank you very much. This site is amazing.

Chiefdone

chiefdone1

Member - Posts: 25

Joined: December 19, 2014

Location: Indiana, United States

Posted: December 22, 2014 at 2:17 PM / IP Logged

On the heavy gauge relay wiring, the wires r like 10 ga. The wires I am supposed to connect to at ignition switch r 18 ga or so. Is this the right place to connect these heavy gauge wires?

Chiefdone

kreg357

Platinum - Posts: 7,783

Joined: January 30, 2009

Location: Pennsylvania, United States

Posted: December 22, 2014 at 2:45 PM / IP Logged

A conditional YES. ( I am not there with my Digital Multi Meter checking and verifying each wire prior to making a nice solder connection.) Does it look like the picture posted earlier? Did you verify the wires with a DMM? It is very common for newer vehicles to have small gauge wires at the main ignition harness. Some wires on new Toyota's are like 26 gauge.

Soldering is fun!

chiefdone1

Member - Posts: 25

Joined: December 19, 2014

Location: Indiana, United States

Posted: December 22, 2014 at 2:53 PM / IP Logged

Yes and yes. Thanks

Chiefdone

chiefdone1

Member - Posts: 25

Joined: December 19, 2014

Location: Indiana, United States

Posted: December 22, 2014 at 3:23 PM / IP Logged

Ok. Brake switch says to look for 12 v when brake pedal pushed. What I see is 5 v. Does the H3 brown wire go on the light green at brake switch?

Chiefdone

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.