auto page 900lcd

Home / the12volt's Install Bay / Car Security and Convenience / auto page 900lcd (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

dstyls

Member - Posts: 37

Joined: January 23, 2008

Posted: January 31, 2008 at 9:27 AM / IP Logged

and i one more thing do i have to install starter kill?because it came with a relay

tedmond

Gold - Posts: 4,610

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: January 06, 2007

Location: Ontario, Canada

Posted: January 31, 2008 at 10:08 AM / IP Logged

well i have used fortin and idatalink. i would pick either, they are both very good units to use. as for starrter kill, it doesnt have to be installed in, but its nice to have. if you decide not to have the starter kill installed, you can use that relay to do your trunk release, that wway you dont spend more money.

dstyls

Member - Posts: 37

Joined: January 23, 2008

Posted: January 31, 2008 at 4:57 PM / IP Logged

and one more thing,on the alarm remote start,it have 2 red,start 1 and 2,and violet.starter(+)output,pink:ignition2(+) output,yellow:ignitio 1(+) output,brown:ac/heater(+) output,i don't understand the violet wire?

tedmond

Gold - Posts: 4,610

Joined: January 06, 2007

Location: Ontario, Canada

Posted: January 31, 2008 at 5:39 PM / IP Logged

Red Wire (2) - probably and most likely your 12v power inputs

Starter Wire 1 and 2 - only one is needed unless you own a toyota or nissan.

Pink - Ignition 2

Yellow - ignition 1

Brown - accessory wire

well those are the wires you will use for sure. im not sure what violet starter is, because no car has 3 starter wires from my experiance. you should test the wires that come off the unit with a DMM (digital multi meter) and see what that does. if your volt meter reads 12v for a second or so, then thats an additional start wire. if you can scan me the unit wiring printout, i can tell you what its for. i used to do some autopage and i think it was used as an additional acc or start wire if needed.

dstyls

Member - Posts: 37

Joined: January 23, 2008

Posted: February 01, 2008 at 10:18 AM / IP Logged

this what is say in the installatin manual

here's the website,its on page 6,7,8

http://www.autopageusa.com/resources/RS-900%20Install%20-0702011.pdf

and thank's again for your help

tedmond

Gold - Posts: 4,610

Joined: January 06, 2007

Location: Ontario, Canada

Posted: February 01, 2008 at 4:06 PM / IP Logged

Connector H1 (6 pin) heres what they have

Violet - starter wire

Red (2) - fused 12v

Yellow - Ignition 1

Pink - Ignition 2

Brown - Accessory or Blower Motor.

dont get confused with Gay/Black - (-) 200mA Starter 2 Output. this is used to power up an additional relay for starter wire 2 if your car has one. remeber anything that you see that has a NEGATIVE Output Rated @ 250mA, its usually used to drive a relay.

puffyd

Member - Posts: 3

Joined: February 04, 2008

Posted: February 04, 2008 at 6:53 PM / IP Logged

Has anyone installed this in any 05+ Dodge Chargers? I had it installed in mine and my instrument lights will not go off when key is in ignition and brake pedal is stepped on. Anyone know what is the cause of this?

tedmond

Gold - Posts: 4,610

Joined: January 06, 2007

Location: Ontario, Canada

Posted: February 04, 2008 at 9:41 PM / IP Logged

did u install it yourself or did a shop/certified dealer install it? if you had it done at a shop bring it back and ask them why its doing that. they coer warrenty for that stuff. if you did it urself make sure u put the parking lights throught a 1.6k ohm resistor .

puffyd

Member - Posts: 3

Joined: February 04, 2008

Posted: February 04, 2008 at 10:35 PM / IP Logged

i had a friend install it who has experience putting in car alarms but has never installed one for a charger...so my problem is the parking lights isnt running through a 1.6k ohm resistor?

dstyls

Member - Posts: 37

Joined: January 23, 2008

Posted: February 05, 2008 at 7:53 AM / IP Logged

hey i'm half way done with the installment but i having trouble with the door lock,is the big wire grey and brown for the small wires,is it the door control module or switch?are you sure you don't need relays,thank's for all your help tedmond

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.