2008 mustang window mod 530t

Home / the12volt's Install Bay / Car Security and Convenience / 2008 mustang window mod 530t (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

StealthEs

Copper - Posts: 326

Joined: September 04, 2003

Location: New Jersey, United States

Posted: July 01, 2008 at 2:55 PM / IP Logged

Has anyone done a 530T in the newer mustangs. In Directechs it lists the wires as motor part of module. Doing any tomorrow andthough I'd ask to see if anyone has any tips to make it easier.

Cris

hazeleye94

Member - Posts: 11

Joined: January 26, 2006

Location: United States

Posted: July 17, 2008 at 1:04 AM / IP Logged

I would like to know if you got this installed successfully... I attempted to install on in my car and found that the one-touch module is integrated with the motor inside the door. I could not find a way to interface between the module since in was part of the motor. If anyone has any advice I sure would appreciate it. Thanks...

StealthEs

Copper - Posts: 326

Joined: September 04, 2003

Location: New Jersey, United States

Posted: July 17, 2008 at 10:01 PM / IP Logged

Ran into the same problem as you did so was unable to integrate the windows.

Cris

i am an idiot

Platinum - Posts: 13,667

This member consistently provides reliable information

Joined: September 21, 2006

Location: Louisiana, United States

Posted: July 17, 2008 at 10:27 PM / IP Logged

Does the one touch module work for up and down? Or only down? Can you get to the back of the window switches easily? When the window is all the way up and you press the up switch, does the window try to go up? or does it know it is at the top of the stroke?

hazeleye94

Member - Posts: 11

Joined: January 26, 2006

Location: United States

Posted: July 18, 2008 at 9:58 AM / IP Logged

The one touch works for both directions. The back of the window switches are easy to get to. It seems that it knows it is already up, when you press the up switch I don't hear the window motor relay click or anything. Also, keep in mind that the new mustangs have the option where when you open the door, the window falls about an inch, then when you close the door, the window goes back up. Very strage issue.

i am an idiot

Platinum - Posts: 13,667

Joined: September 21, 2006

Location: Louisiana, United States

Posted: July 18, 2008 at 6:13 PM / IP Logged

This is what I am thinking, you will have to let me know if you think it is worth trying or not. You said that the one touch function is built into the motor. We need to see if the window switch provides a pulse for the one touch or if the wire on the switch stays at a positive or ground state the entire time the window is moving. IF it pulses the wire and the motor takes it over from there, all we should have to do is pulse that wire and keep the power getting to the motor long enough to roll up from the bottom of the stroke. If the window knows when it gets to top of stroke and shuts off on its own this should work. You may have to use 2 relays. One will provide a high current supply to trigger a relay with a decent size capacitor across 85 and 86 to give you a few seconds of latch. How long does it take for the window to get from bottom to top with the motor not running and the door closed?

hazeleye94

Member - Posts: 11

Joined: January 26, 2006

Location: United States

Posted: July 22, 2008 at 9:37 AM / IP Logged

I will have to check this out when I have time and let you know. I will be at the beach for mustang week until the 28th, so I will investigate and let you know... thanks for the idea.

hazeleye94

Member - Posts: 11

Joined: January 26, 2006

Location: United States

Posted: August 03, 2008 at 10:17 PM / IP Logged

I found a browsable PDF service manual that has the wiring diagram for the window modules and switch. If anyone can make some better sense out of it than me, please feel free to let me know what you think. Or what may work. Here it is...

https://iihs.net/fsm/?dir=40&viewfile=Power%20Windows.pdf

i am an idiot

Platinum - Posts: 13,667

Joined: September 21, 2006

Location: Louisiana, United States

Posted: August 03, 2008 at 11:06 PM / IP Logged

In the drivers door module, there is a wire labeled DACC it is RED / Lt.Blue in color. I am assuming that it is a switched voltage on this wire to only allow the window to work when the key is on. Can you verify that there is 12 volts on this wire only when the key is on or until you open the door?

The WHITE/ black wire is the window up wire. There will be 12 volts on that wire when the window is traveling in up direction, I need to know if there is ground on the violet/lt.green wire when the window is traveling up? I can't tell if there is ground on this wire only when auto up is activated. Attach red lead to the WHITE/ black wire. Black lead to the violet/lt.green wire. Now roll window up without activating auto up. Is there 12 volts displayed on your meter? If not do it again this time activating the auto up feature. Let me know what you find out.

hazeleye94

Member - Posts: 11

Joined: January 26, 2006

Location: United States

Posted: August 07, 2008 at 10:46 AM / IP Logged

i am an idiot wrote:

I will try and check this out this weekend when I get time. Thanks for the help. Maybe we can get this straightened out!

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.