viper 4704v ’07 4 runner

Home / the12volt's Install Bay / Car Security and Convenience / viper 4704v ’07 4 runner (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

c_hawks

Member - Posts: 41

Joined: October 20, 2012

Location: Alaska, United States

Posted: October 21, 2012 at 4:30 PM / IP Logged

smokeman1 wrote:

You should have a 10, 12, anf 14 pin connectors

Of the three 10, 12, 14 which connector is the one I need to hook to for the TX & RX for the immoblizer? If I even have an transponder key.

C_Hawks

2009 Toyota Tacoma Access cab

4 cylinder, manual trans

kreg357

Platinum - Posts: 7,783

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: January 30, 2009

Location: Pennsylvania, United States

Posted: October 21, 2012 at 5:04 PM / IP Logged

Info from iDatalink for Tacoma 2005-2010 40 Bit Key

Transponder 7 Pin connector

Code (RX) pin 4 Pink/Green (DATA)

TXCT (TX) pin 5 LtGREEN/ Red (DATA)

Separate connector

Keysense GREEN/ Black (-) @ Ignition switch

Once again, are you sure the DB-ALL bypass module has the correct ( 401.TL1 Ver 2.19 ) firmware loaded on it?

Soldering is fun!

c_hawks

Member - Posts: 41

Joined: October 20, 2012

Location: Alaska, United States

Posted: October 21, 2012 at 5:22 PM / IP Logged

kreg357 wrote:

Info from iDatalink for Tacoma 2005-2010 40 Bit Key

Transponder 7 Pin connector

Code (RX) pin 4 Pink/Green (DATA)

TXCT (TX) pin 5 LtGREEN/ Red (DATA)

Separate connector

Keysense GREEN/ Black (-) @ Ignition switch

Once again, are you sure the DB-ALL bypass module has the correct ( 401.TL1 Ver 2.19 ) firmware loaded on it?

Thanks Kreg357 I have that info the issue I am having is that the 7-pin connector that the instructions and everyone has been telling me where it is, is not where it is said to be. So I do not know for sure if I even have the transponder key system on my truck.

Well come to find out no it does not have the correct firmware loaded in it. It has to be loaded prior to installation. Bad planning on my part. Guess either I need to go to a local install shop and see if they will upload it for me or by the XKLOADER caable to do it myself. wiz poor planning on my part.

Thanks for the help and info.... back to the drawing board.

C_Hawks

2009 Toyota Tacoma Access cab

4 cylinder, manual trans

lurch228

Silver - Posts: 1,338

Joined: August 08, 2012

Posted: October 21, 2012 at 5:52 PM / IP Logged

c_hawks wrote:

The 30 Flex on the H3/7 is that the same as the Flex Relay? There is no 30 Flex just eh flowing:

ON AUX/AHUTDAOWN HARNESS

(-) 200mA Flex relay control output

ON REMOTE START, 8-Pin connector

Pin 2 - RED / White (+) 12VDC constant input for ignition2 & flex relays

Pin 6 - Pink/White (+) Ignition 1 / Flex relay output

Thanks for the help. I just don't want to screw this up.

Pin 7 - Pink/Black (+) Flex relay input 87A key side (if required) of Flex Relay

So I guess the question is which flex to hook up?

Sorry was thinking 10 pin H3

H3/2 RED / White_ to vehicle +12v WHITE/ Blue

H3/6 Pink/White is Ignition 2 to vehicle BLUE / YELLOW

lurch228

Silver - Posts: 1,338

Joined: August 08, 2012

Posted: October 21, 2012 at 5:57 PM / IP Logged

The 2009 is the same as 2010 so use this pictorial for reference.

https://www.the12volt.com/installbay/forum_posts.asp~TID~130004

lurch228

Silver - Posts: 1,338

Joined: August 08, 2012

Posted: October 21, 2012 at 6:09 PM / IP Logged

You will also need a additional relay for the second starter.

H2/18 VIOLET / YELLOW (-) 200mA STARTER OUTPUT to additional relay( pin 86 and 87 to 12V+, pin 85 to H2/18(starter output), pin 30 to vehicle starter 2 wire (BLACK/ white) and pin 87a open.

lurch228

Silver - Posts: 1,338

Joined: August 08, 2012

Posted: October 21, 2012 at 6:13 PM / IP Logged

Don't forget to add a Fuse between the WHITE/ Red (Vehicle) and 86 & 87 (Add on Relay) connection.

c_hawks

Member - Posts: 41

Joined: October 20, 2012

Location: Alaska, United States

Posted: October 21, 2012 at 6:16 PM / IP Logged

What type of relay do I need? and possible locations of finding it with out using online if I can?

What amp of fuse?

C_Hawks

2009 Toyota Tacoma Access cab

4 cylinder, manual trans

lurch228

Silver - Posts: 1,338

Joined: August 08, 2012

Posted: October 21, 2012 at 6:25 PM / IP Logged

30 amp fuse and any local car stero shop (Around $5)should sell the to you or radioshack should have them for alot more money.

c_hawks

Member - Posts: 41

Joined: October 20, 2012

Location: Alaska, United States

Posted: October 21, 2012 at 6:27 PM / IP Logged

Thanks

C_Hawks

2009 Toyota Tacoma Access cab

4 cylinder, manual trans

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.