clifford 590.2 toggle switch off

Home / the12volt's Install Bay / Car Security and Convenience / clifford 590.2 toggle switch off (

Topic Closed)

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

smokeman1

Platinum - Posts: 1,589

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: February 17, 2013 at 7:45 AM / IP Logged

Time to recheck the ground on the H2/18, make sure the connector is in tight. Check the toggle switch with a DMM for continunity and make sure it is plugged in tight. Check the H2/18 for continunity also. Until you get that issue cleared it won't start.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

pentavolvo

Copper - Posts: 241

Joined: September 30, 2003

Location: United States

Posted: February 17, 2013 at 8:58 AM / IP Logged

bypass switch all together

adrianotech

Copper - Posts: 53

Joined: February 01, 2013

Location: Connecticut, United States

Posted: February 17, 2013 at 12:50 PM / IP Logged

I grounded the ( on ) side of switch and the remote started but I noticed that bypass is not working ,because I had to open the door with the old keyless entry remote control to remote start with the new one....... when I open the door with the old one that allow to start the engine in 30 seconds...

adriantech

adrianotech

Copper - Posts: 53

Joined: February 01, 2013

Location: Connecticut, United States

Posted: February 17, 2013 at 12:53 PM / IP Logged

so that means the switch was defective.

adriantech

adrianotech

Copper - Posts: 53

Joined: February 01, 2013

Location: Connecticut, United States

Posted: February 20, 2013 at 9:24 AM / IP Logged

Now I have another isue the remote start works only when I open the door with old keyless remote control , could that be a start kill relay installed previewsly , when I open the door a led start flash rapidly for about 15 seconds , i'm supposed to start the car between open the door to the ligh stop flash rapidly.

adriantech

adrianotech

Copper - Posts: 53

Joined: February 01, 2013

Location: Connecticut, United States

Posted: February 22, 2013 at 8:17 PM / IP Logged

anybody know how to connect the parking lights in element 2003 ?

adriantech

pentavolvo

Copper - Posts: 241

Joined: September 30, 2003

Location: United States

Posted: February 22, 2013 at 8:27 PM / IP Logged

PARKING LIGHTS ( - ) BLUE (-) @ FACTORY ALARM Plug

NOTE #3; THE FACTORY ALARM PLUG IS LOCATED LEFT OF THE STEERING COLUMN IN A

GREEN PLUG.

adrianotech

Copper - Posts: 53

Joined: February 01, 2013

Location: Connecticut, United States

Posted: February 22, 2013 at 8:46 PM / IP Logged

I did it but the light flash just when unlock the door ,not when lock ,not whe start the vehicle...

adriantech

adrianotech

Copper - Posts: 53

Joined: February 01, 2013

Location: Connecticut, United States

Posted: February 23, 2013 at 9:25 AM / IP Logged

any help to connect parking light wires ?

adriantech

adrianotech

Copper - Posts: 53

Joined: February 01, 2013

Location: Connecticut, United States

Posted: March 03, 2013 at 8:45 AM / IP Logged

I can't set ignition controlled door lock unlock on clifford 590.2 it is not responding , is possible set these ficture with data mode on idatalink ? or i have to switch to w2w ?

adriantech

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.