bitwriter

Home / the12volt's Install Bay / Car Security and Convenience / bitwriter (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

antonic

Member - Posts: 14

Joined: September 14, 2013

Location: Australia

Posted: November 17, 2013 at 7:27 AM / IP Logged

Hi, I have a Directed "DEI ProSecurity SAA998T Programming Tool" with Version 1.5 chip. Will the upgrade V2.9 chip work in my unit and do I need to upgrade the ROM microprocessor too?

Is it possible to flash my current v1.5 chip with the v2.9 firmware if I have an IC programmer?

Thanks in advance...

antonic

Member - Posts: 14

Joined: September 14, 2013

Location: Australia

Posted: November 24, 2013 at 5:59 AM / IP Logged

Anyone?

smokeman1

Platinum - Posts: 1,588

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: November 24, 2013 at 7:06 AM / IP Logged

I have a v2.6 chip that you can have. PM me your address.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

smokeman1

Platinum - Posts: 1,588

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: November 25, 2013 at 12:45 PM / IP Logged

Mailed out today. Hope it works for your Programer.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

antonic

Member - Posts: 14

Joined: September 14, 2013

Location: Australia

Posted: December 16, 2013 at 6:58 AM / IP Logged

Thanks Smokeman1!

It worked flawlessly.

smokeman1

Platinum - Posts: 1,588

Joined: September 14, 2009

Location: Wisconsin, United States

Posted: December 16, 2013 at 2:03 PM / IP Logged

Excellent! bitwriter -- posted image.

When all else fails, Read the Instructions

Support the12volt.com Make a Donation

brandfnnew

Member - Posts: 1

Joined: December 16, 2013

Posted: December 17, 2013 at 12:05 AM / IP Logged

Hey antonic, I also just purchased the SAA998T programmer with the Ver 1.5 chip and am planning on upgrading to the 2.9 chip. Did you also need to upgrade the 998M memory module as well for it to work correctly?

antonic

Member - Posts: 14

Joined: September 14, 2013

Location: Australia

Posted: December 17, 2013 at 12:12 AM / IP Logged

brandfnnew wrote:

I'm not too sure, Smokeman gave me a V2.6 Chip and it worked. Didn't have to change memory module...

antonic

Member - Posts: 14

Joined: September 14, 2013

Location: Australia

Posted: January 04, 2014 at 6:05 AM / IP Logged

Just read that my bitwriter is an old version and it will require both 998M board and 998U EEPROM chip.

http://www.drdetailshop.com/Bitwriter_Upgrade.pdf

lucasoil4u

Copper - Posts: 317

Joined: May 11, 2009

Location: Minnesota, United States

Posted: January 07, 2014 at 11:49 AM / IP Logged

the upgrade is very easy to do

LMK if you have questions

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.