Remote start cant change settings?

Home / the12volt's Install Bay / Car Security and Convenience / Remote start cant change settings?

Welcome Guest :)

Members

< Prev Page Next Page > < Prev Topic Next Topic >

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: January 07, 2018 at 1:13 PM / IP Logged

Is this an auto? If so ground the ebrake status wire, if manual connect ebrake switch.

On Euro GM, d-ALL wouldn't recognise brake via data.

bill7774

Member - Posts: 32

Joined: December 21, 2017

Location: Ohio, United States

Posted: January 07, 2018 at 2:14 PM / IP Logged

It's a manual. I will try to wire it direct to the ebrake. It's a flashlogic flcan btw. Thanks.

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: January 07, 2018 at 2:43 PM / IP Logged

You missed the point these modules are similar and they DON'T always do what it says on the label, just ground that wire for now.

bill7774

Member - Posts: 32

Joined: December 21, 2017

Location: Ohio, United States

Posted: January 07, 2018 at 3:07 PM / IP Logged

No I understand. I already tried to put it in auto trans. mode and ground the wire for diagnosis. I will try in manual mode again when I get home.

howie ll

Pot Metal - Posts: 16,466

Joined: January 09, 2007

Location: United Kingdom

Posted: January 07, 2018 at 5:10 PM / IP Logged

Are you setting it up via manual transmission reservation and by the way, you can test that ebrake lead black/white at the R/Start it should go to ground with ignition and ebrake on.

bill7774

Member - Posts: 32

Joined: December 21, 2017

Location: Ohio, United States

Posted: January 08, 2018 at 2:19 PM / IP Logged

Finally got it working. I had the ignition wire hooked up wrong (no power while cranking). Thanks for all the assistance Howie. Everything seems to be working properly now.

bill7774

Member - Posts: 32

Joined: December 21, 2017

Location: Ohio, United States

Posted: January 09, 2018 at 1:57 PM / IP Logged

Thought I had it working. The alarm goes off when I remote start. The only way to cancel the alarm is to hit the remote start button and then unlock. If I dont cut off the remote start the alarm doesn't respond to the unlock button on the keyfob. Any suggestions?

bill7774

Member - Posts: 32

Joined: December 21, 2017

Location: Ohio, United States

Posted: January 09, 2018 at 2:43 PM / IP Logged

I figured it out. I had to change the setting, ign-controlled locks to option 2, lock and unlock. I believe I had to do this with my 02 Jetta as well. I couldn't remember what I did is why I asked. Remote start cant change settings? - Page 3 -- posted image.

Remote start cant change settings? - Page 3 -- posted image.

bill7774

Member - Posts: 32

Joined: December 21, 2017

Location: Ohio, United States

Posted: January 09, 2018 at 9:23 PM / IP Logged

I spoke to soon. Sometimes the alarm still goes off with remote start activation. Not always. Come to think of it my 02 jetta does the same thing. I can click unlock first and then remote start and the alarm wont go off. That works but would prefer to get it to work properly. Any suggestions?

geepherder

Platinum - Posts: 3,668

This member consistently provides reliable information

Joined: October 27, 2003

Posted: January 09, 2018 at 10:23 PM / IP Logged

Hardwire the factory alarm disarm wire.

My ex once told me I have a perfect face for radio.

< Prev Page Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.