05 pacifica wont start with key

Home / the12volt's Install Bay / Car Security and Convenience / 05 pacifica wont start with key (

Topic Closed)

Welcome Guest :)

Members

Next Page > < Prev Topic Next Topic >

ls1nova

Member - Posts: 15

Joined: February 12, 2004

Posted: January 27, 2007 at 1:06 PM / IP Logged

I just got the entire remote start done and I went to program the tach and now it won't start with the key. The security light comes on solid and it won't crank at all. Help please.

I did have an issue when I was programing the CHU.2 While I was doing it the battery went all but dead (just my luck) I couldn't have erased the program from the 2 factory remotes could I?

Thanks a ton,

Frank

Velocity Motors

Moderator - Posts: 12,488

This member has made a donation to the12volt.com. Click here for more info.

This member has been recognized as an authority in Electrical Theory. Click here for more info.

This member has been recognized as an authority in Fabrication. Click here for more info.

This member has been recognized as an authority in Mobile Audio and Video. Click here for more info.

This member has been recognized as an authority in Mobile Security and Convenience. Click here for more info.

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: January 27, 2007 at 1:50 PM / IP Logged

Disconnect the PKU-CH2 and make sure that the battery is fully charged. Try place the key into the cylinder but do not turn it over. Take note of the LED in the dash just to make sure that the LED goes out after 3 seconds after ignition is turned to the ON position.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

Search for other posts by Velocity Motors

ls1nova

Member - Posts: 15

Joined: February 12, 2004

Posted: January 27, 2007 at 2:06 PM / IP Logged

it does go out.

I disconected the battery and tried it. The horn honked 3 times and it still won't start.

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: January 27, 2007 at 2:08 PM / IP Logged

Disconnect the PKU-CH2 and make sure that the battery is fully charged.Try to start without the bypass module in the loop.

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

ls1nova

Member - Posts: 15

Joined: February 12, 2004

Posted: January 27, 2007 at 2:09 PM / IP Logged

I actually have everything unhooked from the ign. wires right now and it still won't do anything. It must went into some type of tamper mode or something. Is there any way to get it out of that mode?

Thanks,

Frank

ls1nova

Member - Posts: 15

Joined: February 12, 2004

Posted: January 27, 2007 at 2:15 PM / IP Logged

The module is unhooked also. Still no go.

au5599

Copper - Posts: 94

Joined: December 22, 2005

Location: United States

Posted: January 27, 2007 at 7:24 PM / IP Logged

disconnect all wires going to any starter wires then try it again. did you happen to check all fuses to make sure you didnt blow one?

Street Dreams Car Club

93 GRAND CARAVAN SE / Astro

Team New York SS3-4 06 & SM3-4 07 DB Drag World Finals

2003 Chevy Suburban LT / 98 GTP

Velocity Motors

Moderator - Posts: 12,488

Joined: March 08, 2002

Location: Manitoba, Canada

Posted: January 28, 2007 at 12:57 AM / IP Logged

Have you tried both keys ?

Jeff

Velocity Custom Home Theater

Mobile Audio/Video Specialist

Morden, Manitoba CANADA

ls1nova

Member - Posts: 15

Joined: February 12, 2004

Posted: January 28, 2007 at 7:29 AM / IP Logged

Yes. Neither one will do anything. Is there any way to reset the Chrysler's like the GM vehicles? Like leaving the key on for so long or something along those lines.

Thanks,

Frank

splaudio

Copper - Posts: 237

Joined: January 22, 2006

Posted: January 28, 2007 at 7:51 AM / IP Logged

did u check ur fuses like said above? that a dmm and check to see if ur ignition wire has power when the key is turned to on...

Next Page >

Printable version

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Search the12volt.com

Follow the12volt.com

Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.