the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
icon

no luck with xk04


Post ReplyPost New Topic
< Prev Topic Next Topic >
rtperformance 
Member - Posts: 17
Member spacespace
Joined: August 13, 2007
Location: United States
Posted: September 15, 2007 at 11:33 PM / IP Logged  
Also try to reset the XK04 by unplugging the mod. then push and hold the program button, plug XK04 back in, LED comes on hold button till LED gose off. bypass is now reset. program bypass.
todds440 
Member - Posts: 48
Member spacespace
Joined: December 29, 2006
Location: United States
Posted: September 16, 2007 at 7:29 AM / IP Logged  
If you go to bypasskits under the pk04 module instalation guide.  Theres some trouble shooting tips.  1)  If LED stays on solid or flashes rapidly ,reverse the tx and rx wire connections.  2) If module fails to program make sure brown wire is not getting a trickle ground from remote starter prior to last programming step. 3) Fails to program reset module  Hope this might help.
extreme1 
Silver - Posts: 1,070
Silver spacespace
Joined: February 12, 2003
Location: Canada
Posted: September 16, 2007 at 11:08 AM / IP Logged  
well, here in the trenches, we've tryed many times on the escape and have given up, they'll program, work for a few times and quit, same with the fusion and explorer. If you unplug the xk04 and plug in a pkf3 it works fine and for good. eliminates wiring errors from the equation.
when you sell 1000's of remote starters a year you don't have time to troubleshoot problems like this so it's just best to avoid them, the idatalink bypass works 100% of the time on all fords.
Shaughn Murley
Install Manager, Dealer Services
Visions Electronics
Red Deer, Alberta
chadwa2003 
Copper - Posts: 353
Copper spacespace
Joined: January 08, 2005
Location: Canada
Posted: September 16, 2007 at 5:35 PM / IP Logged  
I used to idata link on an 08 escape no problems and never needed reprogramming
tragik 
Copper - Posts: 169
Copper spacespace
Joined: September 28, 2005
Location: Alaska, United States
Posted: September 17, 2007 at 4:17 PM / IP Logged  

Call Tech suppoprt and have them send you a software update called PKf3.0.2

I had this same issue with a 06 mountaineer. The new software did the trick. The wiring is the same, but you have to add the orange wire on the module to an ignition source.

Northstart.....or start it your damn self.
dea,can 
Copper - Posts: 284
Copper spacespace
Joined: January 12, 2006
Location: Saskatchewan, Canada
Posted: September 18, 2007 at 2:10 AM / IP Logged  
its work with the key close to factory ring i just zip strip it  it works for me thanks  for your help.
dragon
Page of 2

Sorry, you can NOT post a reply.
This topic is closed.

  Printable version Printable version Post ReplyPost New Topic
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

  •  
Search the12volt.com
Follow the12volt.com Follow the12volt.com on Facebook
Thursday, March 28, 2024 • Copyright © 1999-2024 the12volt.com, All Rights Reserved Privacy Policy & Use of Cookies
Disclaimer: *All information on this site ( the12volt.com ) is provided "as is" without any warranty of any kind, either expressed or implied, including but not limited to fitness for a particular use. Any user assumes the entire risk as to the accuracy and use of this information. Please verify all wire colors and diagrams before applying any information.

Secured by Sectigo
the12volt.com spacer
the12volt.com spacer
the12volt.com spacer
Support the12volt.com
Top
the12volt.com spacer
the12volt.com spacer